Sponsored Content
Full Discussion: Routing Problem
Special Forums IP Networking Routing Problem Post 32463 by norsk hedensk on Tuesday 26th of November 2002 04:18:46 PM
Old 11-26-2002
the etc/hosts files defines ip address and associates hostnames with those addresses, essentially the hosts file is like a small name server, or more correctly a name database. the first thing your computer looks at when you try to connect to a website or anything on the net with a name, the computer looks at the /etc/hosts file first. so this is not the file where you set up your routing. without that default gateway you cannot connect to the internet. now, to set that up first you must find out what your default gateway is, you have to contact your isp. if you have broadband like dsl or cable, and you are using a router, your default gateway probably is 192.168.1.1 or 192.168.0.1. to set this up you will need to visit the man pages for ifconfig, and route.
man ifconfig
man route
now to set your default gateway, you do that with route. the man page for route does a good job of telling you how to do that. make sure you include the GW parameter when you figure our how to use route, this parameter tells your system that the ip address you supply will be the current default gateway. after that, you should be up and running!
 

10 More Discussions You Might Find Interesting

1. IP Networking

Routing problem

Hi I know this problem is more likely some windows problem but it has also something to do with unix. We have a windows nt environment wich uses AIX (unix) machines as file servers (samba). In our windows network environment we nicely see al the unix file servers via the 10 MB network. Last... (2 Replies)
Discussion started by: Mark Detrez
2 Replies

2. IP Networking

routing problem

following Problem. I configured my SuSE Linux 8.0 as a router. I4l, named, ip_forward, iptables (NAT/MASQUERADING) are running or are aktivatet. I just can get a internet connection about the proxy server squid, but if i want to use other protocols i need functional routing. (I had this... (1 Reply)
Discussion started by: razor
1 Replies

3. IP Networking

routing problem in solaris

hi, below is the situation: my server is in 128.10.200.xxx network. i have a solaris computer running in a subnet. this computer got 2 nic card. 1 is 172.18.198.xxx , another 1 is 10.100.xxx.11 there is a machine stick with this computer, ip is 10.100.xxx.12 so, 10.100.xxx.11 and... (3 Replies)
Discussion started by: kyhah
3 Replies

4. IP Networking

Specific routing problem help needed

Hi, I am trying to set up the following : - One linux box connected to the net, static address, eth0 - No other eth interface on the box I want to set up this box in a way it can accept remote connections, like pptp tunnels (which seems the easier to set up unless you have other idea)... (2 Replies)
Discussion started by: aerostar700
2 Replies

5. Solaris

Routing problem of Solaris

Hi, I got problem of Sun Solaris 8 routing. IP of SunA is 10.16.64.164, and have routing table: 10.16.64.0 10.16.64.164 U 1 19236 bge1 10.6.0.0 10.6.0.3 U 1 16534 bge0 224.0.0.0 10.6.0.3 U 1 ... (4 Replies)
Discussion started by: milo
4 Replies

6. Red Hat

routing problem...im missing something

hi, having an issue on a class C network with trying to get a redhat diskless setup going. I am using oracle enterprise 5, which is RHEL 5.3 i believe. here is the scenario: sun sparc m4k that i am planning on making the red hat boxes boot off after i get the network issue fixed. ... (3 Replies)
Discussion started by: caddyjoe77
3 Replies

7. AIX

Aix Routing Problem

I need the following solution , please help me... Current situation ip: 192.168.0.12 persistent and 192.168.254.12 service ip gateway: 192.168.0.254 subnet: 255.255.255.0 i have added a new ip on a new nic ip: 10.10.255.40 gateway: 10.10.255.62 subnet: 255.255.255.224 ... (1 Reply)
Discussion started by: rajibimran
1 Replies

8. IP Networking

routing problem/question

Internet Gateway 192.168.0.201 Server 1 192.168.0.101 192.168.1.101 192.168.2.101 gateway: 192.168.0.201 VIP: 192.168.1.100 VIP: 192.168.2.100 Server 2 192.168.0.102 192.168.1.102 192.168.2.102 gateway: 192.168.0.201 Client 1 192.168.2.201 gateway: 192.168.2.100 (1 Reply)
Discussion started by: hopfensp
1 Replies

9. Solaris

Routing problem

Hi, I have two physical interfaces on a servers. We have connected them to differerent subnets. 1) First interface: 10.158.49.87 to newtwork 10.158.49.0, its gateway is 10.158.49.1 (It is added as default gateway) It is existing set up. It works well 2) Second interface: ... (1 Reply)
Discussion started by: sri243
1 Replies

10. IP Networking

Routing problem : two interfaces one gateway

hi folks, i have a horstbox-router with the following configuration. it has 4 ethernet ports from wich one (wan0) is configured as an external modem via dhcp. at this port/interface(wan0) it is connected with my home network (other switch). this configuration results in the following... (14 Replies)
Discussion started by: gencaslan
14 Replies
VDE_L3(1)						      General Commands Manual							 VDE_L3(1)

NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch. SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket] DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup for each -v option given at command line. Static routes to target networks can be defined using the -r option. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 -v /var/run/s2.ctl:10.0.0.254/255.255.0.0 connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in each network can specify the vde_l3 as their gateway to reach the other one. OPTIONS
-v vde_plug:ipaddress/netmask Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One can define as many interfaces as she wants. -r target_network/netmask:gateway Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she wants. -G default_gw Specify a default gateway, to be used whenever no static route is defined for a target host. -M mgmt_socket the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be used as a remote terminal for wirefilter. NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik" i.e. the German "Association for Electrical, Electronic & Information Technologies"). SEE ALSO
vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1). AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net> VDE is a project by Renzo Davoli <renzo@cs.unibo.it> Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)
All times are GMT -4. The time now is 05:44 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy