11-20-2002
those missing files are C libraries. what your compliling is uses those libraries in its source code, look around on the net and you should be able to find all of those to install, i dont know if turbolinux has a packaging system, where you run a program and you can check off boxes of what you want to install, but try looking for a C resource website, and you should be able to find those libraries that you need.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm way confused. I loaded RH 7.1 on an old P-75 Compaq. IT has an EtherExpress pro/100 card in it and I have that attached to the optional port on our firewall with a crossover....I can't seem to get the card to negotiate with the firewall...it's currently 100Meg at Half duplex. I'm at a loss... (3 Replies)
Discussion started by: kwalter
3 Replies
2. IP Networking
Hi
I need to know how a driver for a network interface card works, I want to learn the basic principles since I know that every driver has its specific implementation.
For example when we speak about the scheduler, we can read an operating system book and learn general design concepts e.g.... (0 Replies)
Discussion started by: Puntino
0 Replies
3. SCO
hi
I have a fresh installation of SCO 5.0.6 and I have download a NIC driver for Intel Pro 1000:
ftp://ftp.sco.com/pub/openserver5/507/drivers/eeG_5.0.7g/VOL.000.000
Howto install it using floppy?
---------- Post updated at 04:02 PM ---------- Previous update was at 02:18 PM... (0 Replies)
Discussion started by: ccc
0 Replies
4. UNIX for Advanced & Expert Users
Hi, all:
How can I know whether the packets recieved from network by my own NIC driver are transmitted to upper layer(IP layer) or not?
How can I know if the packets come from upper layer are passed to my own NIC driver and go out further?
Is there any shell command or utility show... (9 Replies)
Discussion started by: liklstar
9 Replies
5. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
6. Solaris
Hi guys
My friend needs nfo driver for his Solaris box. I installed that driver for myself from scratch and he needs that driver in SVR4 format. I downloaded source code and run make and this is the point I don't how to proceed.
How can I recognize which needs go to the package ?
Does make... (0 Replies)
Discussion started by: solaris_user
0 Replies
7. UNIX for Advanced & Expert Users
Hi, all:
My writed NIC driver for rtl8139d adapter on linux 3.0.4 cannot send and recieve simultaneously but is able to send or recieve in parallel respectively. As soon as it send and recieve at the same time, the transmmition rate on both directions gradually decrease to zero b/s and report... (0 Replies)
Discussion started by: liklstar
0 Replies
8. Programming
Hi, all:
My writed NIC driver for rtl8139d adapter on linux 3.0.4 cannot send and recieve simultaneously but is able to send or recieve in parallel respectively. As soon as it send and recieve at the same time, the transmmition rate on both directions gradually decrease to zero b/s and report... (1 Reply)
Discussion started by: liklstar
1 Replies
9. Solaris
In Solaris 10 it was easy, a simple grep through modinfo output and you'd have the version of any loaded module, including your NIC drivers. In my career I've seen many people relying on this information in their scripts. Now I'm on Solaris 11, and where have the version numbers gone? The... (0 Replies)
Discussion started by: cambridge
0 Replies
10. Hardware
My NIC driver, which is writed by myself, didn't pass high pressure test!
I writed a shell script in which the key commands are "scp" to test the driver under high pressure. The shell script loop 3000 times and in each loop, the scp command transmits 1GB data.
When the test fail, it... (2 Replies)
Discussion started by: liklstar
2 Replies
LEARN ABOUT CENTOS
debuginfo-install
debuginfo-install(1) debuginfo-install(1)
NAME
debuginfo-install - install debuginfo packages and their dependencies
SYNOPSIS
debuginfo-install package
DESCRIPTION
debuginfo-install is a program which installs the RPMs needed to debug the specified package. The package argument can be a wildcard, but
will only match installed packages. debuginfo-install will then enable any debuginfo repositories, and install the relevant debuginfo rpm.
EXAMPLES
Download and install all the RPMs needed to debug the kernel RPM:
debuginfo-install kernel
WARNING MESSAGES
Could not find debuginfo for:
You may sometimes see warning messages about certain packages not being found if you run debuginfo-install for a wildcard or glob.
Debuginfo packages are not necessary for "noarch" RPMs; these will generate a warning message. Additionally, On 64-bit systems, no
multilib debuginfo packages are published, so if you have 32-bit packages installed, these will also generate warning messages.
FILES
As debuginfo-install uses YUM libraries for retrieving all the information, it relies on YUM configuration for its default values like
which repositories to use. Consult YUM documentation for details:
/etc/yum.conf
/etc/yum/repos.d/
/var/cache/yum/
SEE ALSO
yum.conf (5)
http://yum-utils.baseurl.org/
http://yum.baseurl.org/
AUTHORS
See the Authors file included with this program.
BUGS
There are of course no bugs, but should you find any, you should first consult the FAQ section on http://yum.baseurl.org/wiki/Faq and if
unsuccessful in finding a resolution contact the mailing list: yum-devel@lists.baseurl.org. To file a bug use http://bugzilla.redhat.com
for Fedora/RHEL/Centos related bugs and http://yum.baseurl.org/report for all other bugs.
James Antill 21 October 2008 debuginfo-install(1)