Sponsored Content
Full Discussion: Network Card Help
Top Forums UNIX for Advanced & Expert Users Network Card Help Post 32033 by The Fridgerator on Sunday 17th of November 2002 02:09:50 PM
Old 11-17-2002
i figured out the problem. I viewed the output from dmesg and found:
PCI: this computer doesnt support PCI

so i added "pci=bios" to the entry for redhat8 and it works fine now.
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies

3. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

4. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies

5. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

6. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

7. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies

8. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies

9. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies

10. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
npe(7D) 							      Devices								   npe(7D)

NAME
npe - PCI Express bus nexus driver DESCRIPTION
The npe nexus driver is used on X64 servers for PCI Express Root Complex devices that provide PCI Express interconnect. This driver is com- pliant to PCI Express base specification, Revision 1.0a. This nexus driver provides support for the following features: Access to extended configuration space, IEEE 1275 extensions for PCI Express, Base line PCI Express error handling and PCI Express MSI interrupts. FILES
/platform/i86pc/kernel/drv/npe 32-bit ELF kernel module. /platform/i86pc/kernel/drv/amd64/npe 64-bit ELF kernel module. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+------------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+------------------------------+ |Architecture |x64 PCI Express-based systems | +-----------------------------+------------------------------+ |Availability |SUNWcakr.i | +-----------------------------+------------------------------+ SEE ALSO
attributes(5), pcie(4), pcie_pci(7D) PCI Express Base Specification v1.0a -- 2003 Writing Device Drivers IEEE 1275 PCI Bus Binding -- 1998 http://playground.sun.com/1275/bindings/pci/pci-express.txt SunOS 5.11 12 Oct 2005 npe(7D)
All times are GMT -4. The time now is 12:42 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy