11-17-2002
OK... new problem kindof... but its almost the same.
I had to take off slacwkare. Then i put on RedHat8.0 and it wouldnt load teh module for my sis900 card.
I did modprobe sis900 and this is what happened:
[root@localhost src]# modprobe sis900
/lib/modules/2.4.18-14/kernel/drivers/net/sis900.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including inva
lid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.18-14/kernel/drivers/net/sis900.o: insmod /lib/modules/2.4.18-1
4/kernel/drivers/net/sis900.o failed
/lib/modules/2.4.18-14/kernel/drivers/net/sis900.o: insmod sis900 failed
I have redhat 7.2 on the computer too and my sis900 module works fine. I really need to get the sis900 working, is there anything else i should try to get it to work?
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
6. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
7. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
8. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT ULTRIX
modules-load.d
MODULES-LOAD.D(5) modules-load.d MODULES-LOAD.D(5)
NAME
modules-load.d - Configure kernel modules to load at boot
SYNOPSIS
/etc/modules-load.d/*.conf
/run/modules-load.d/*.conf
/usr/lib/modules-load.d/*.conf
DESCRIPTION
systemd-modules-load.service(8) reads files from the above directories which contain kernel modules to load during boot in a static list.
Each configuration file is named in the style of /etc/modules-load.d/program.conf. Note that it is usually a better idea to rely on the
automatic module loading by PCI IDs, USB IDs, DMI IDs or similar triggers encoded in the kernel modules themselves instead of static
configuration like this. In fact, most modern kernel modules are prepared for automatic loading already.
CONFIGURATION FORMAT
The configuration files should simply contain a list of kernel module names to load, separated by newlines. Empty lines and lines whose
first non-whitespace character is # or ; are ignored.
CONFIGURATION DIRECTORIES AND PRECEDENCE
Configuration files are read from directories in /etc/, /run/, and /lib/, in order of precedence. Each configuration file in these
configuration directories shall be named in the style of filename.conf. Files in /etc/ override files with the same name in /run/ and
/lib/. Files in /run/ override files with the same name in /lib/.
Packages should install their configuration files in /lib/. Files in /etc/ are reserved for the local administrator, who may use this logic
to override the configuration files installed by vendor packages. All configuration files are sorted by their filename in lexicographic
order, regardless of which of the directories they reside in. If multiple files specify the same option, the entry in the file with the
lexicographically latest name will take precedence. It is recommended to prefix all filenames with a two-digit number and a dash, to
simplify the ordering of the files.
If the administrator wants to disable a configuration file supplied by the vendor, the recommended way is to place a symlink to /dev/null
in the configuration directory in /etc/, with the same filename as the vendor configuration file. If the vendor configuration file is
included in the initrd image, the image has to be regenerated.
EXAMPLE
Example 1. /etc/modules-load.d/virtio-net.conf example:
# Load virtio-net.ko at boot
virtio-net
SEE ALSO
systemd(1), systemd-modules-load.service(8), systemd-delta(1), modprobe(8)
systemd 237 MODULES-LOAD.D(5)