Network Card Help Post: 32018

Sponsored Content

Top Forums UNIX for Advanced & Expert Users Network Card Help Post 32018 by The Fridgerator on Sunday 17th of November 2002 12:11:36 AM

11-17-2002

Registered User

OK... new problem kindof... but its almost the same.
I had to take off slacwkare. Then i put on RedHat8.0 and it wouldnt load teh module for my sis900 card.
I did modprobe sis900 and this is what happened:

[root@localhost src]# modprobe sis900
/lib/modules/2.4.18-14/kernel/drivers/net/sis900.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including inva
lid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.18-14/kernel/drivers/net/sis900.o: insmod /lib/modules/2.4.18-1
4/kernel/drivers/net/sis900.o failed
/lib/modules/2.4.18-14/kernel/drivers/net/sis900.o: insmod sis900 failed

I have redhat 7.2 on the computer too and my sis900 module works fine. I really need to get the sis900 working, is there anything else i should try to get it to work?

The Fridgerator

View Public Profile for The Fridgerator

Find all posts by The Fridgerator

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the...

2. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out.

3. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But...

4. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and...

5. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated.

6. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks

7. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see...

8. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks !

9. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101...

10. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4...

LEARN ABOUT SUNOS

insmod

INSMOD(8)                                                             insmod                                                             INSMOD(8)

NAME

       insmod - Simple program to insert a module into the Linux Kernel

SYNOPSIS

       insmod [filename] [module options...]

DESCRIPTION

       insmod is a trivial program to insert a module into the kernel. Most users will want to use modprobe(8) instead, which is more clever and
       can handle module dependencies.

       Only the most general of error messages are reported: as the work of trying to link the module is now done inside the kernel, the dmesg
       usually gives more information about errors.

COPYRIGHT

       This manual page originally Copyright 2002, Rusty Russell, IBM Corporation. Maintained by Jon Masters and others.

SEE ALSO

       modprobe(8), rmmod(8), lsmod(8), modinfo(8)

AUTHORS

       Jon Masters <jcm@jonmasters.org>
           Developer

       Lucas De Marchi <lucas.de.marchi@gmail.com>
           Developer

kmod                                                                01/28/2018                                                           INSMOD(8)

10 More Discussions You Might Find Interesting

1. IP Networking

network card

Discussion started by: cparks

2. UNIX for Dummies Questions & Answers

Installing network card

Discussion started by: gops

3. IP Networking

Network Card with SGI

Discussion started by: DPAI

4. UNIX for Dummies Questions & Answers

Network card and internet

Discussion started by: Gibbler