11-17-2002
OK... new problem kindof... but its almost the same.
I had to take off slacwkare. Then i put on RedHat8.0 and it wouldnt load teh module for my sis900 card.
I did modprobe sis900 and this is what happened:
[root@localhost src]# modprobe sis900
/lib/modules/2.4.18-14/kernel/drivers/net/sis900.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including inva
lid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.18-14/kernel/drivers/net/sis900.o: insmod /lib/modules/2.4.18-1
4/kernel/drivers/net/sis900.o failed
/lib/modules/2.4.18-14/kernel/drivers/net/sis900.o: insmod sis900 failed
I have redhat 7.2 on the computer too and my sis900 module works fine. I really need to get the sis900 working, is there anything else i should try to get it to work?
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
6. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
7. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
8. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT DEBIAN
opensc-tool
OPENSC-TOOL(1) OpenSC tools OPENSC-TOOL(1)
NAME
opensc-tool - generic smart card utility
SYNOPSIS
opensc-tool [OPTIONS]
DESCRIPTION
The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
sending arbitrary APDU commands to a card.
OPTIONS
--info, -i
Print information about OpenSC, such as version and enabled components
--atr, -a
Print the Answer To Reset (ATR) of the card, output is in hex byte format
--name, -n
Print the name of the inserted card (driver)
--serial
Print the card serial number (normally the ICCSN), output is in hex byte format
--send-apdu apdu, -s apdu
Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF...
--list-files, -f
Recursively lists all files stored on card
--list-readers, -l
Lists all configured readers
--list-drivers, -D
Lists all installed card drivers
--reader num, -r num
Use the given reader number. The default is 0, the first reader in the system.
--card-driver driver, -c driver
Use the given card driver. The default is auto-detected.
--wait, -w
Wait for a card to be inserted
--verbose, -v
Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.
SEE ALSO
opensc-explorer(1)
opensc 06/03/2012 OPENSC-TOOL(1)