11-14-2002
What Unix are you using?
If you are unsure, post the results of the command "uname -a"...
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How can i set an permanent route so that itīs still here after a reboot ?
i have a gateways file
Thanks
:confused: :confused: :confused: (1 Reply)
Discussion started by: redcrosskbg
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I'm trying to connect to a network device, with the connection follwoing the UNIX routing table we set up. Its to go via a specific network Gateway and out throught a specific Lan card (Lan4). However when trying to conenct it keeps going through Lan3 and will not get to its destination.... (3 Replies)
Discussion started by: nhatch
3 Replies
3. IP Networking
hi all,
how to access ip routing table throgh program,
how should i integrate my rip routing table with the ip routing table :) (0 Replies)
Discussion started by: vinodkumar
0 Replies
4. AIX
i have AIX Unix with "dynamic routing table" service enabled, but i do not need this service. How i can disable this service.
thanks (1 Reply)
Discussion started by: jdsnbr
1 Replies
5. IP Networking
hi all...
i need to know, where is locate the routing table on sun solaris, how i can saved the configuration....
because when i restart the server, lost the configuration....
thank you...
Regards... (3 Replies)
Discussion started by: chanfle
3 Replies
6. IP Networking
Hi all,
I am confusing with routing table, i use linux and iptables.
i have 1 internet gateway, and 1 router for VPN.
here is my network.
eth0=192.168.0.1
eth1=192.168.100.1
192.168.0.0/24 --- eth0(Linux Box)eth1 ---(DSL)---Internet
|
... (4 Replies)
Discussion started by: blesets
4 Replies
7. Linux
Hello,
how to make entries in routing table perminent (1 Reply)
Discussion started by: teenasuresh
1 Replies
8. Red Hat
I have below routing table in linux kernel 2.6.9
# netstat -rn
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
10.155.24.0 0.0.0.0 255.255.252.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U ... (5 Replies)
Discussion started by: chuikingman
5 Replies
9. IP Networking
Hello.
Is there any way to restore back the default ip routing table ?
For example, my current routing table is something like
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
109.123.95.0 0.0.0.0 255.255.255.0 U 0 ... (0 Replies)
Discussion started by: anid
0 Replies
10. HP-UX
Hi all,
Could someone please explain to me how I should read this routing table,
# netstat -rn
Routing tables
Destination Gateway Flags Refs Interface Pmtu
127.0.0.1 127.0.0.1 UH 0 lo0 32808
10.222.47.82 10.222.47.82 UH... (3 Replies)
Discussion started by: rachael
3 Replies
optisa(1) User Commands optisa(1)
NAME
optisa - determine which variant instruction set is optimal to use
SYNOPSIS
optisa instruction_set...
DESCRIPTION
optisa prints which instruction_set out of the ones specified in the command will perform best on this machine. In this case, ``best''
is defined by the order in which instruction set names are returned by isalist(1). Possible values for instruction_set are given in
isalist(5).
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
EXIT STATUS
The following exit values are returned:
0 One of the instruction_set values you specified is printed by this command.
1 There is no output; that is, this machine cannot use any instruction_set that you specified with the optisa command.
SEE ALSO
isalist(1), uname(1), attributes(5), isalist(5)
NOTES
optisa is preferable to uname -p or uname -m (see uname(1)) in determining which of several binary versions of a given program should be
used on the given machine.
SunOS 5.10 25 Jul 1997 optisa(1)