|
|
Sponsored Content
Top Forums
UNIX for Advanced & Expert Users
Network Card Help
Post 31798 by PxT on Wednesday 13th of November 2002 02:30:00 PM
11-13-2002
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
6. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
7. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
8. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies