Sponsored Content
Full Discussion: HP-UX Network Configuration
Operating Systems HP-UX HP-UX Network Configuration Post 30798 by S.Vishwanath on Monday 28th of October 2002 08:20:00 AM
Old 10-28-2002
Here is the more info regarding the configuration.

LAB consists of all the machines with IP range falling under xxx.xxx.71.nn. The HP-UX machine falls under this Range.

Our workstations falls under xxx.xxx.37.nn.

I'm able to ping all machines & vice-versa in the xxx.xxx.71.nn domian with my HP-UX machine.

Also, all systems from xxx.xxx.37.nn can ping to all systems in xxx.xxx.71.nn & vice-versa but other than this HP-UX machine.

I'm trying all this ping & telnet using IP address only.

I have also configured the DNS for this HP-UX machine using sam. ie. it has created the resolv.conf with the appropriate DNS entries that I did specify.

But still I'm not able to resolve or communicate from the workstation.

Do I need to introduce an entry regarding this HP-UX machine into the DNS server Forcefully ?????????

I would like to enlight on this that currently I'm using only IP address for communication & not the Hostname.

Since I have updated the DNS configuration on the HP-UX machine, If I telnet to this system from with in xxx.xxx.71.nn machine, it take a very long time to open the login session. If I remove the DNS configuration from the HP-UX machine, then telnet from other machines from the same IP range is absolutely faster.

Last edited by S.Vishwanath; 10-28-2002 at 10:53 AM..
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network configuration in Solaris 8

Hi. I have installed Solaris 8 and I am trying to configure the network settings. For some reason every time I reboot, my card loses its configuration. I can run ifconfig and the only IP address bound to my card (on either interface) is 127.0.0.1. I can change that to a valid IP address on my... (8 Replies)
Discussion started by: Ask Me
8 Replies

2. IP Networking

Network Configuration for SunSparsh 5.8

Hi, I need to configure the Network for a Sun Solaris systems. The OS info is SunOS Sparsh 5.8 Generic_108528-13 Sun4u Sparc SUNW,Ultra-250. Please do let me know, how shall I shart with & more in configuring the Network. Below is the list of Network Configuration I need to Make ... (2 Replies)
Discussion started by: S.Vishwanath
2 Replies

3. Solaris

network configuration

hi again... i configured my network settings sometiime ago using the sys-unconfig command.the active link was rtls0. there was some problem with the network so i changed the ISP. now when im trying to reconfigure the system wit sys-unconfig, it tries to configure the network on rtls1 (and shows... (1 Reply)
Discussion started by: strider
1 Replies

4. Solaris

Specifying network configuration info

Can someone please point me in the correct direction of where I configure the network information on SunOS 5.8 server? (Searching SunSolve and Google have resulted in thousands of fixes for potential errors, but I can't find the general instructions, etc. for starting the process). Thanks! (2 Replies)
Discussion started by: FredSmith
2 Replies

5. UNIX for Dummies Questions & Answers

Network Configuration Commands.....

I need to know what commands I will need to use to change a host name, IP Address, and network configurations (routerings, dns, etc) and a Unix SCO machine. Also, if there is any short tutorials on using the commands, i would defiently like that information. Thanks!!! (1 Reply)
Discussion started by: HandleX
1 Replies

6. SCO

Network Configuration

I have a SCO 5.07 Server and I am trying to get it on my network. I have edited the /etc/hosts file and /etc/rc2.d/s99route . I has connectivity on the NIC card but not sure if I am forgetting another file. Thanks! (2 Replies)
Discussion started by: andrewd
2 Replies

7. UNIX for Dummies Questions & Answers

network configuration

I am using solaris 10, my internet works alright but each time i reboot i keep loosing my connection. I will have to use the ifconfig iprb0 192.168.1.xx netmask 255.255.255.0 up and Route add default 192.168.1.xxx command to gain back my internet. I know there is a better way of addressing... (1 Reply)
Discussion started by: seyiisq
1 Replies

8. Solaris

Network configuration

Hi I have installed Solaris 5.10 on Intel x86 machine (standalone). I want to access internet through solaris. How should I configure the network? Is static IP or DHCP advisable? (5 Replies)
Discussion started by: johnl
5 Replies

9. Solaris

Problem in network configuration

Hi everybody, I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem. I have 2 unix machines absolutely identical running solaris 9. For network reasons I need to change the IP address of the 2 machines. I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies

10. UNIX for Advanced & Expert Users

network configuration on openbsd

Hi all, I got following configuration problem I need to configure tiny network on openbsd I got server1 with 3 interfaces vic0 em0 em1 The interface vic0 on server1 has follwoing IP 172.16.1.1 em0 firstly I would like to configure network under em0 (I have assigned to em0 following... (1 Reply)
Discussion started by: kvok
1 Replies
face(1)                                                            User Commands                                                           face(1)

NAME
face - executable for the Framed Access Command Environment Interface SYNOPSIS
face [-i init_file] [-c command_file] [-a alias_file] [filename...] DESCRIPTION
The Framed Access Command Environment Interface (FACE) presents your files and file folders on the screen through a system of menus and forms if you are properly set up as a FACE user. filename must follow the naming convention Menu.xxx for a menu, Form.xxx for a form, and Text.xxx for a text file, where xxx is any string that conforms to the UNIX system file naming conventions. The Form and Menu Language Interpreter (FMLI) descriptor lifetime will be ignored for all frames opened by argument to face. These frames have a lifetime of immortal by default. If filename is not specified on the command line, the FACE Menu will be opened along with those objects specified by the LOGINWIN environment variables. These variables are found in the user's .environ file. OPTIONS
The following options are supported: -a alias_file Alias file -c command_file Command file -i init_file Initial file OPERANDS
The following operand is supported: filename The full pathname of the file describing the object to be opened initially. EXIT STATUS
The face command will return a non-zero exit value if the user is not properly set up as a FACE user. FILES
$HOME/pref/.environ ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWfac | +-----------------------------+-----------------------------+ SEE ALSO
env(1), attributes(5) SunOS 5.10 5 Jul 1990 face(1)
All times are GMT -4. The time now is 09:04 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy