10-24-2002
Almost sounds like the remote host was blocking the pings. Are you able to get anything from it?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi there hope list can help
I'm looking for a command that does the following
lets say i ping a server 00.00.000.00
and this server is up and running how do i get the ping command to return a UP or a Down
meaning
if the command is true do this
if the command is False do this
... (2 Replies)
Discussion started by: nemex
2 Replies
2. AIX
We can ping out but the return never comes back even to localhost
ping localhost
PING loopback: (127.0.0.1): 56 data bytes
64 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=0 ms
it just sits there....
any ideas, any files to check (1 Reply)
Discussion started by: csaunders
1 Replies
3. UNIX for Dummies Questions & Answers
Hi ,
I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this?
sam70 (1 Reply)
Discussion started by: sam70
1 Replies
4. IP Networking
hi,
I m trying to ping ip on the network . The machine is started but i can't access and can't ping it .. But when i restarts that machine that works fine..... can anybody have an idea about this problem ??
if then reply ..
thanks (2 Replies)
Discussion started by: tahir23
2 Replies
5. Linux
Hi All,
Need your help one more time.
I am trying to ping a linux machine which is not responding to ping.
However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0".
It is not happening in the... (1 Reply)
Discussion started by: ailnilanjan
1 Replies
6. IP Networking
I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative.
... (7 Replies)
Discussion started by: Rutgerncas
7 Replies
7. Shell Programming and Scripting
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies
8. IP Networking
I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Discussion started by: oslbhavana
6 Replies
9. Shell Programming and Scripting
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies
10. Programming
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
RMCPING(8) System Manager Commands RMCPING(8)
NAME
rmcpping - send RMCP Ping to network hosts
SYNOPSIS
rmcpping [OPTION...] destination
DESCRIPTION
rmcpping uses the RMCP Ping request datagram to elicit an RMCP Pong response from a remote host. The utility can be used to verify if a
remote host supports RMCP or IPMI. The initial starting sequence number will be randomized. rmcpping will return 0 to the environment if
it receives atleast 1 response from the remote host. Otherwise, it exits with a value of 1.
OPTIONS
The following options are available
-h Output help menu.
-V Output version.
-c count
Stop after sending count packets.
-i interval
Wait interval seconds between sending each packet. The default is to wait for one second between each packet.
-I interface address
Set source address to specified interface address. Argument may be numeric IP address or name of device.
-t timeout
Time to wait for a response, in seconds. Default is five seconds.
-v Verbose output.
-s num Specify an initial starting sequence number. The default is to use a random initial sequence number.
-d Turn on debugging.
KNOWN ISSUES
It has been observed that some remote BMCs can get "confused" and delay packet responses if duplicate packets (with duplicate sequence num-
bers) are sent in succession very quickly. There is no known way to cleanly deal with a "confused" BMC other than the wait awhile.
Unlike ping(8), local network devicess (e.g. 127.0.0.1) cannot be "pinged".
REPORTING BUGS
Report bugs to <freeipmi-users@gnu.org> or <freeipmi-devel@gnu.org>.
COPYRIGHT
Copyright (C) 2007-2012 Lawrence Livermore National Security, LLC.
Copyright (C) 2003-2007 The Regents of the University of California.
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 3 of the License, or (at your option) any later version.
ORIGIN
Command and manpage based off ping(8).
SEE ALSO
freeipmi(7), ping(8), ipmiping(8)
http://www.gnu.org/software/freeipmi/
rmcpping 1.1.5 2012-06-15 RMCPING(8)