10-24-2002
Almost sounds like the remote host was blocking the pings. Are you able to get anything from it?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi there hope list can help
I'm looking for a command that does the following
lets say i ping a server 00.00.000.00
and this server is up and running how do i get the ping command to return a UP or a Down
meaning
if the command is true do this
if the command is False do this
... (2 Replies)
Discussion started by: nemex
2 Replies
2. AIX
We can ping out but the return never comes back even to localhost
ping localhost
PING loopback: (127.0.0.1): 56 data bytes
64 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=0 ms
it just sits there....
any ideas, any files to check (1 Reply)
Discussion started by: csaunders
1 Replies
3. UNIX for Dummies Questions & Answers
Hi ,
I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this?
sam70 (1 Reply)
Discussion started by: sam70
1 Replies
4. IP Networking
hi,
I m trying to ping ip on the network . The machine is started but i can't access and can't ping it .. But when i restarts that machine that works fine..... can anybody have an idea about this problem ??
if then reply ..
thanks (2 Replies)
Discussion started by: tahir23
2 Replies
5. Linux
Hi All,
Need your help one more time.
I am trying to ping a linux machine which is not responding to ping.
However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0".
It is not happening in the... (1 Reply)
Discussion started by: ailnilanjan
1 Replies
6. IP Networking
I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative.
... (7 Replies)
Discussion started by: Rutgerncas
7 Replies
7. Shell Programming and Scripting
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies
8. IP Networking
I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Discussion started by: oslbhavana
6 Replies
9. Shell Programming and Scripting
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies
10. Programming
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
RSH(1) General Commands Manual RSH(1)
NAME
rsh - remote shell
SYNOPSIS
rsh [-n] [-l username] host [command]
host [-n] [-l username] [command]
DESCRIPTION
Rsh connects to the specified host, and executes the specified command. Rsh copies its standard input to the remote command, the standard
output of the remote command to its standard output, and the standard error of the remote command to its standard error. Interrupt, quit
and terminate signals are propagated to the remote command; rsh normally terminates when the remote command does.
The remote username used is the same as your local username, unless you specify a different remote name with the -l option. This remote
name must be equivalent (in the sense of rlogin(1)) to the originating account; no provision is made for specifying a password with a com-
mand.
If you omit command, then instead of executing a single command, you will be logged in on the remote host using rlogin(1).
Shell metacharacters which are not quoted are interpreted on local machine, while quoted metacharacters are interpreted on the remote
machine. Thus the command
rsh otherhost cat remotefile >> localfile
appends the remote file remotefile to the localfile localfile, while
rsh otherhost cat remotefile ">>" otherremotefile
appends remotefile to otherremotefile.
OPTIONS
-l username
Specify the remote user name.
-n Connect standard input of the remote command to /dev/null. Do this if rsh should not inadvertently read from standard input.
SEE ALSO
rcp(1), rlogin(1), rhosts(5).
BUGS
You cannot run an interactive command (like rogue(6) or vi(1)); use rlogin(1).
4.2 Berkeley Distribution April 29, 1985 RSH(1)