10-24-2002
Almost sounds like the remote host was blocking the pings. Are you able to get anything from it?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi there hope list can help
I'm looking for a command that does the following
lets say i ping a server 00.00.000.00
and this server is up and running how do i get the ping command to return a UP or a Down
meaning
if the command is true do this
if the command is False do this
... (2 Replies)
Discussion started by: nemex
2 Replies
2. AIX
We can ping out but the return never comes back even to localhost
ping localhost
PING loopback: (127.0.0.1): 56 data bytes
64 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=0 ms
it just sits there....
any ideas, any files to check (1 Reply)
Discussion started by: csaunders
1 Replies
3. UNIX for Dummies Questions & Answers
Hi ,
I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this?
sam70 (1 Reply)
Discussion started by: sam70
1 Replies
4. IP Networking
hi,
I m trying to ping ip on the network . The machine is started but i can't access and can't ping it .. But when i restarts that machine that works fine..... can anybody have an idea about this problem ??
if then reply ..
thanks (2 Replies)
Discussion started by: tahir23
2 Replies
5. Linux
Hi All,
Need your help one more time.
I am trying to ping a linux machine which is not responding to ping.
However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0".
It is not happening in the... (1 Reply)
Discussion started by: ailnilanjan
1 Replies
6. IP Networking
I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative.
... (7 Replies)
Discussion started by: Rutgerncas
7 Replies
7. Shell Programming and Scripting
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies
8. IP Networking
I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Discussion started by: oslbhavana
6 Replies
9. Shell Programming and Scripting
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies
10. Programming
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
LEARN ABOUT DEBIAN
smokeping_probes_skel
Smokeping_probes_skel(3) SmokePing Smokeping_probes_skel(3)
NAME
Smokeping::probes::skel - a skeleton for Smokeping Probes
SYNOPSIS
*** Probes ***
+skel
forks = 5
offset = 50%
step = 300
timeout = 15
# The following variables can be overridden in each target section
pings = 5
# [...]
*** Targets ***
probe = skel # if this should be the default probe
# [...]
+ mytarget
# probe = skel # if the default probe is something else
host = my.host
pings = 5
DESCRIPTION
This is a non-functional module that is intended to act as a basis for creation of new probes. See the smokeping_extend document for more
information.
VARIABLES
Supported probe-specific variables:
forks
Run this many concurrent processes at maximum
Example value: 5
Default value: 5
offset
If you run many probes concurrently you may want to prevent them from hitting your network all at the same time. Using the probe-
specific offset parameter you can change the point in time when each probe will be run. Offset is specified in % of total interval, or
alternatively as 'random', and the offset from the 'General' section is used if nothing is specified here. Note that this does NOT
influence the rrds itself, it is just a matter of when data acqusition is initiated. (This variable is only applicable if the variable
'concurrentprobes' is set in the 'General' section.)
Example value: 50%
step
Duration of the base interval that this probe should use, if different from the one specified in the 'Database' section. Note that the
step in the RRD files is fixed when they are originally generated, and if you change the step parameter afterwards, you'll have to
delete the old RRD files or somehow convert them. (This variable is only applicable if the variable 'concurrentprobes' is set in the
'General' section.)
Example value: 300
timeout
How long a single 'ping' takes at maximum
Example value: 15
Default value: 5
Supported target-specific variables:
pings
How many pings should be sent to each target, if different from the global value specified in the Database section. Note that the
number of pings in the RRD files is fixed when they are originally generated, and if you change this parameter afterwards, you'll have
to delete the old RRD files or somehow convert them.
Example value: 5
AUTHORS
Niko Tyni <ntyni@iki.fi>,
SEE ALSO
smokeping_extend
2.6.8 2013-03-17 Smokeping_probes_skel(3)