hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
hi there !
i have exactly the same problem like this guy here
https://www.unix.com/shell-programming-scripting/127668-getting-curl-output-verbose-file.html
i am not able to save the curl verbose output..
the sollution in this thread (redirecting stderr to a file) does not work for me.... (0 Replies)
Hi,
My linux server working with LVM partition and with /boot partition, now my /boot partition is full, now i need to extend my boot partition. can i know how to do it, without any data loss.
Regards,
M.Selva Prakash (4 Replies)
Hello Folks,
Greetings,
I am in need of extending the / partition for one of my SuSE linux Enterprise Server 11.1 which is running on VMware. I will be able to extend the virtual lun from the vshphere console but not sure how to extend the root partition from the OS end. I am not sure if I... (1 Reply)
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
hi all,
As going thru LVM concepts in rhel 6, got hit with a question about "how to use the raw partition of an harddisk which extended volume is taken a bit"
please find the attached diagram...
is it possible to use this raw space with previously created extended partition without data... (13 Replies)
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
I am trying to modify the "corestat v1.1" code which is in Perl.The typical output of this code is below:
Core Utilization
CoreId %Usr %Sys %Total
------ ----- ----- ------
5 4.91 0.01 4.92
6 0.06 ... (0 Replies)
Hi,
I need to extend a soft partition from 20G to 100G. New disk is already added as a meta device. This soft partition is already assigned to a guest LDOM. Can someone let me know the steps to increase soft partition so guest LDOM can recognize the new space.
Thanks (1 Reply)
Discussion started by: Gho
1 Replies
LEARN ABOUT NETBSD
disktab
DISKTAB(5) BSD File Formats Manual DISKTAB(5)NAME
disktab -- disk description file
SYNOPSIS
#include <disktab.h>
DESCRIPTION
disktab is a simple database which describes disk geometries and disk partition characteristics. It is used to initialize the disk label on
the disk. The format is patterned after the termcap(5) terminal data base. Entries in disktab consist of a number of `:' separated fields.
The first entry for each disk gives the names which are known for the disk, separated by `|' characters. The last name given should be a
long name fully identifying the disk.
The following list indicates the normal values stored for each disk entry.
Name Type Description
ty str Type of disk (e.g. removable, winchester)
dt str Type of controller (e.g. SMD, ESDI, floppy)
ns num Number of sectors per track
nt num Number of tracks per cylinder
nc num Total number of cylinders on the disk
sc num Number of sectors per cylinder, ns*nt default
su num Number of sectors per unit, sc*nc default
se num Sector size in bytes, DEV_BSIZE default
sf bool Controller supports bad144-style bad sector forwarding
rm num Rotation speed, rpm, 3600 default
sk num Sector skew per track, default 0
cs num Sector skew per cylinder, default 0
hs num Headswitch time, usec, default 0
ts num One-cylinder seek time, usec, default 0
il num Sector interleave (n:1), 1 default
d[0-4] num Drive-type-dependent parameters
bs num Boot block size, default BBSIZE
sb num Superblock size, default SBSIZE
ba num Block size for partition `a' (bytes)
bd num Block size for partition `d' (bytes)
be num Block size for partition `e' (bytes)
bf num Block size for partition `f' (bytes)
bg num Block size for partition `g' (bytes)
bh num Block size for partition `h' (bytes)
fa num Fragment size for partition `a' (bytes)
fd num Fragment size for partition `d' (bytes)
fe num Fragment size for partition `e' (bytes)
ff num Fragment size for partition `f' (bytes)
fg num Fragment size for partition `g' (bytes)
fh num Fragment size for partition `h' (bytes)
oa num Offset of partition `a' in sectors
ob num Offset of partition `b' in sectors
oc num Offset of partition `c' in sectors
od num Offset of partition `d' in sectors
oe num Offset of partition `e' in sectors
of num Offset of partition `f' in sectors
og num Offset of partition `g' in sectors
oh num Offset of partition `h' in sectors
pa num Size of partition `a' in sectors
pb num Size of partition `b' in sectors
pc num Size of partition `c' in sectors
pd num Size of partition `d' in sectors
pe num Size of partition `e' in sectors
pf num Size of partition `f' in sectors
pg num Size of partition `g' in sectors
ph num Size of partition `h' in sectors
ta str Partition type of partition `a' (4.2BSD filesystem, swap, etc)
tb str Partition type of partition `b'
tc str Partition type of partition `c'
td str Partition type of partition `d'
te str Partition type of partition `e'
tf str Partition type of partition `f'
tg str Partition type of partition `g'
th str Partition type of partition `h'
FILES
/etc/disktab
SEE ALSO getdiskbyname(3), disklabel(5), disklabel(8), newfs(8)HISTORY
The disktab description file appeared in 4.2BSD.
BSD June 5, 1993 BSD