hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
hi there !
i have exactly the same problem like this guy here
https://www.unix.com/shell-programming-scripting/127668-getting-curl-output-verbose-file.html
i am not able to save the curl verbose output..
the sollution in this thread (redirecting stderr to a file) does not work for me.... (0 Replies)
Hi,
My linux server working with LVM partition and with /boot partition, now my /boot partition is full, now i need to extend my boot partition. can i know how to do it, without any data loss.
Regards,
M.Selva Prakash (4 Replies)
Hello Folks,
Greetings,
I am in need of extending the / partition for one of my SuSE linux Enterprise Server 11.1 which is running on VMware. I will be able to extend the virtual lun from the vshphere console but not sure how to extend the root partition from the OS end. I am not sure if I... (1 Reply)
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
hi all,
As going thru LVM concepts in rhel 6, got hit with a question about "how to use the raw partition of an harddisk which extended volume is taken a bit"
please find the attached diagram...
is it possible to use this raw space with previously created extended partition without data... (13 Replies)
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
I am trying to modify the "corestat v1.1" code which is in Perl.The typical output of this code is below:
Core Utilization
CoreId %Usr %Sys %Total
------ ----- ----- ------
5 4.91 0.01 4.92
6 0.06 ... (0 Replies)
Hi,
I need to extend a soft partition from 20G to 100G. New disk is already added as a meta device. This soft partition is already assigned to a guest LDOM. Can someone let me know the steps to increase soft partition so guest LDOM can recognize the new space.
Thanks (1 Reply)
Discussion started by: Gho
1 Replies
LEARN ABOUT OSF1
extendfs
extendfs(8) System Manager's Manual extendfs(8)NAME
extendfs - Extends UFS file systems
SYNOPSIS
/sbin/extendfs [- s] [disk_blocks] device_name
DESCRIPTION
Use the extendfs command to increase the storage space in a UFS file system. The file system must not be mounted when you perform this
operation. To extend a mounted (in use) UFS file system, use the mount command with the -o extend option.
The procedure for increasing the storage space of a UFS file system is as follows: Look at the contents the /etc/fstab file to identify the
disk partition that maps to the file system. Ensure that there is available storage space on the target disk as follows: If LSM is in use
on your system, use LSM commands to increase the size of the LSM volume as described in the Logical Storage Manager guide. If LSM is not
in use on your system, use the disklabel command or the diskconfig graphical user interface to check the current size and use of partitions
on the disk. If there is adequate space on an adjacent partition, use the disklabel command to write the current label to a file as fol-
lows: # disklabel -r dsk4 > d4label Edit the disklabel file to change the size of the partition on which your UFS file system resides.
Increase the number of disk blocks on the partition and decrease the disk block size of the adjacent partition by an equivalent number.
Use the disklabel command with the -R option to write the revised label to the raw disk as follows: # disklabel -R /dev/rdisk/dsk4 d4label
When the disk label is revised, extend the file system using the extendfs command. You can either use the full extent of the newly sized
partition or extend the file system in stages. The following example commands show both methods. To extend the file system to use all the
available space, you specify the disk partition on which the file system resides, as follows: # extendfs /dev/disk/dsk4g To extend the
file system to use only part of the available space, you specify a number of disk blocks, as follows: # extendfs -s 300000 /dev/disk/dsk4g
The remainder of the extended partion is reserved for future use.
You can extend a file system as many times as necessary, up to the physical limit of the storage device. When no more space is available
on the storage device, you must back up the file system using the dump command and restore the file system to a storage device that has
more available space.
Once you have extended a file system, the operation cannot be reversed except by a back up and restore operation. Use the dump command to
back up the file system. You can then reset the partition sizes manually and restore the file system to the storage device.
ERRORS
The disklabel command produces output similar to that of the newfs command. If a list of disk blocks is not displayed on the terminal, the
command has failed. Verify the partition settings and the mount status of the target file system.
The disklabel command does not permit you to overwrite a partition if it is in use. Refer to the disklabel(8) reference page for more
information on label errors.
FILES
Specifies the command path.
RELATED INFORMATION diskconfig(8), disklabel(8), mount(8), and fstab(4).
extendfs(8)