04-12-2020
maybe there are some settings about pcie lanes configurable in your intel mainboards bios?
This User Gave Thanks to the-architect For This Post:
9 More Discussions You Might Find Interesting
1. Solaris
Hi ,
I am trying to configure a private LAN and corporate LAN on the same machien on Solaris 10.
How can I achieve this?
Thanks (1 Reply)
Discussion started by: deedee
1 Replies
2. Shell Programming and Scripting
Hi,
I am uising Suse linux on my system and i tried :
man ethtool and i got the manual for ethtool but when i tried to use the command as:
ethtool -a eth0
it says Command not found.
also, i tried rpm -qa|grep ethtool i got:
ethtool-3-15.2 so,it means my system has ethtool server or... (4 Replies)
Discussion started by: salil2012
4 Replies
3. Programming
Hi,
I'm using ethtool to change network settings:
Just for the experiment, i want to change speed to 10, instead of 100,
I type:
ethtool -s eth0 speed 10 duplex full autoneg off
and to view settings i type:
ethtool eth0, and get this:
Settings for eth0:
Supported ports:
... (4 Replies)
Discussion started by: alex889
4 Replies
4. IP Networking
Hello, I've got a FreeBSD 6 server running on my network that I used as a file server for my main computer. However I've really become frustrated with the slow up/down speeds I'm getting, about 100KB/s, which is about as bad as if I was using a "real" server. My setup is as follows:
ISP
|... (4 Replies)
Discussion started by: CyberCat
4 Replies
5. IP Networking
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Discussion started by: lawstudent
3 Replies
6. Shell Programming and Scripting
Hi,
I have a script that, basically, has two input files of this type:
file1
key1=value1_1_1
key2=value1_2_1
key4=value1_4_1
...
file2
key2=value2_2_1
key2=value2_2_2
key3=value2_3_1
key4=value2_4_1
...
My files are 10k lines big each (approx).
The keys are strings that don't... (7 Replies)
Discussion started by: fzd
7 Replies
7. Red Hat
Hi, there is an incompatibility between my NIC and my Western Digital Powerline adapters which appears to cause autonegotiation to fail intermittently, most often following a reboot. Running the following Ethtool script will establish a connection immediately:
#!/bin/sh
# chkconfig: 345 85... (12 Replies)
Discussion started by: torley
12 Replies
8. UNIX and Linux Applications
Hello all. I have VSFTP up and ruining on ubuntu 10.04. It works great inside LAN, however when it comes to using it outside i have some problems. If i try to connect from filezila i get the listing and if i try to download it shows it will take forever to receive a file which is larger then 1mb,... (2 Replies)
Discussion started by: mantas1
2 Replies
9. UNIX for Beginners Questions & Answers
Hi All,
I am trying to find my NIC card speed in centos 5. But i am unable to get the info using ethtool command.
# ethtool eth0
Settings for eth0:
Link detected: yes
and even tried to look for the file # cd /sys/class/net/eth0/speed files which is also not available.... (8 Replies)
Discussion started by: sravani25
8 Replies
LEARN ABOUT CENTOS
powertop
POWERTOP(8) powertop manual POWERTOP(8)
NAME
powertop - a power consumption and power management diagnosis tool.
SYNOPSIS
powertop [ options ]
DESCRIPTION
powertop is a program that helps to diagnose various issues with power consumption and power management. It also has an interactive mode
allowing one to experiment with various power management settings. When invoking powertop without arguments powertop starts in interactive
mode.
OPTIONS
--calibrate
runs powertop in calibration mode. When running on battery, powertop can track power consumption as well as system activity. When
there are enough measurements, powertop can start to report power estimates. One can get more accurate estimates by using this
option to enable a calibration cycle. This will cycle through various display levels and USB device activities and workloads.
--csv[=FILENAME]
generate a CSV report. If a filename is not specified then the default name "powertop.csv" is used. The CSV report can be used for
reporting and data analysis.
--debug
run in "debug" mode.
--extech=devnode
use the Extech Power Analyzer for measurements. This allows one to specify the serial device node of the serial to USB adaptor con-
necting to the Extech Power Analyzer, for example /dev/ttyUSB0.
--help
show the help message.
--html[=FILENAME]
generate an HTML report. If a filename is not specified then the default name "powertop.html" is used. The HTML report can be sent
to others to help diagnose power issues.
--iteration[=iterations]
number of times to run each test.
--workload[=workload]
file to execute for workload.
--quiet
supress stderr output.
--time[=seconds]
generate a report for a specified number of seconds.
--version
print version information and exit.
BUGS
Send bug reports to <powertop@lists.01.org>
SEE ALSO
The program is more fully described at https://01.org/powertop
AUTHOR
powertop was written by Arjan van de Ven <arjan@linux.intel.com>, and is currently maintained by Chris E Ferron <chris.e.fer-
ron@linux.intel.com>.
Linux June 1, 2012 POWERTOP(8)