Hi,
I am uising Suse linux on my system and i tried :
man ethtool and i got the manual for ethtool but when i tried to use the command as:
ethtool -a eth0
it says Command not found.
also, i tried rpm -qa|grep ethtool i got:
ethtool-3-15.2 so,it means my system has ethtool server or... (4 Replies)
Hi,
I'm using ethtool to change network settings:
Just for the experiment, i want to change speed to 10, instead of 100,
I type:
ethtool -s eth0 speed 10 duplex full autoneg off
and to view settings i type:
ethtool eth0, and get this:
Settings for eth0:
Supported ports:
... (4 Replies)
Hello, I've got a FreeBSD 6 server running on my network that I used as a file server for my main computer. However I've really become frustrated with the slow up/down speeds I'm getting, about 100KB/s, which is about as bad as if I was using a "real" server. My setup is as follows:
ISP
|... (4 Replies)
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Hi,
I have a script that, basically, has two input files of this type:
file1
key1=value1_1_1
key2=value1_2_1
key4=value1_4_1
...
file2
key2=value2_2_1
key2=value2_2_2
key3=value2_3_1
key4=value2_4_1
...
My files are 10k lines big each (approx).
The keys are strings that don't... (7 Replies)
Hi, there is an incompatibility between my NIC and my Western Digital Powerline adapters which appears to cause autonegotiation to fail intermittently, most often following a reboot. Running the following Ethtool script will establish a connection immediately:
#!/bin/sh
# chkconfig: 345 85... (12 Replies)
Hello all. I have VSFTP up and ruining on ubuntu 10.04. It works great inside LAN, however when it comes to using it outside i have some problems. If i try to connect from filezila i get the listing and if i try to download it shows it will take forever to receive a file which is larger then 1mb,... (2 Replies)
Hi All,
I am trying to find my NIC card speed in centos 5. But i am unable to get the info using ethtool command.
# ethtool eth0
Settings for eth0:
Link detected: yes
and even tried to look for the file # cd /sys/class/net/eth0/speed files which is also not available.... (8 Replies)
Discussion started by: sravani25
8 Replies
LEARN ABOUT LINUX
pcic
PCIC(4) BSD Kernel Interfaces Manual PCIC(4)NAME
pcic -- PC Card bridge driver
SYNOPSIS
device pcic
device pccard
DESCRIPTION
The pcic driver provides support for older ISA and non-Yenta PCI PC Card bridges. The pcic driver supports most ExCA devices attached to the
ISA bus or PCI devices that do not conform to the Yenta specification.
The following ISA devices, or true clones, are supported in the current code.
Intel i82365SL Step A
Intel i82365SL Step B
Intel i82365SL Step C Intel's original 16-bit PC Card controller.
Intel i82365SL-DF Intel's last version of this device. 3.3V support was added.
VLSI 82C146 An older VLSI part with some issues on some machines.
Cirrus Logic PD-6710
Cirrus Logic PD-6720
Cirrus Logic PD-6722 Cirrus Logic's pcic controller. Compatible with the i82365SL Step C with the addition of a different 3.3V control.
Ricoh RF5C296
Ricoh RF5C396 Ricoh's PC Card bridge chips. These are compatible with the i82365SL Step C, but with yet another different 3.3V con-
trol.
Vadem 365
Vadem 465 Compatible with i82365SL Step C.
Vadem 468
Vadem 469 Like the earlier Vadem models, but with Vadem's own, incompatible, 3.3V control system.
IBM PCIC IBM clone of the original i82365SL part, with its own ID register value. Has no 3.3V ability.
Many other vendors made parts in this arena, but most of them were compatible with one of the above chipsets.
The following PCI pcmcia bridges are supported:
Cirrus Logic PD6729
Cirrus Logic PD6730
O2micro OZ6729
O2micro OZ6730
BUGS
This does not work at all at the moment.
BSD July 9, 2002 BSD