04-10-2020
Hi....You can keep local time with the TimeLib.h library. This runs from the processor's clock. You use NTP time from the network to periodically "true up" your local time. See TimeNTP example in the Time library and NTPClient in the ESP8266WiFi libarary.
10 More Discussions You Might Find Interesting
1. Windows & DOS: Issues & Discussions
All,
I have a Windows XP client which I need to get time synchronized from a Linux ntp server. What are the commands to perform the setup and configuration?
Thanks,
Mike (1 Reply)
Discussion started by: bubba112557
1 Replies
2. Solaris
All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Discussion started by: bubba112557
1 Replies
3. Fedora
Hello All
I have a problem about ntp, I am install a ntp server on a fedora 11 machine and I have 8 ntp client (solaris 10) everything working fine but just a server can not sync time . I have receive this error message
-bash-3.00# ntptime
ntp_gettime() returns code 5 (ERROR)
time... (1 Reply)
Discussion started by: bogacd
1 Replies
4. Linux
All,
I need to write a script which can determine if my NTP client is X second off from the NTPD server time. I am looking for a crafty oneliner to calculate the time difference? (3 Replies)
Discussion started by: vada010
3 Replies
5. AIX
Hello everybody! When I run command "ntpdate" the following error occures
"ksh: ntpdate: 0403-006 Execute permission denied.
"
# oslevel -s
5300-08-06-0918
oslevel -r
5300-08
eny suggestion friends? :-) (3 Replies)
Discussion started by: wwwzviadi
3 Replies
6. Solaris
Hi, I am trying to configure NTP client on my Solaris server, but I am getting error like:
Jan 13 10:53:33 SPOTS ntpdate: no server suitable for synchronization foundMy ntp.conf file:
bash-3.00# pwd
/etc/inet
bash-3.00#
bash-3.00#
bash-3.00# cat ntp.conf
# ident "@(#)ntp.client... (5 Replies)
Discussion started by: nypreH
5 Replies
7. Solaris
How to add offset to NTP client so that, for eg., clock is -20 seconds? (2 Replies)
Discussion started by: orange47
2 Replies
8. Solaris
hi all
ntp client side configuration file is done but in
# ntpq -p
remote refid st t when poll reach delay offset disp
==============================================================================
ntpserver .INIT. 16 u - 64 0 0.00 0.000... (5 Replies)
Discussion started by: nikhil kasar
5 Replies
9. Red Hat
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
10. Programming
Currently have two ESP8266 modules testing some Blynk apps, whereI'm not so happy with the Blynk business model for developers, but that's another story.
So, with two of my ESP8266s currently "busy", I decided to work on the ESP32, and in particular the ESPWROOM32.
I installed the... (0 Replies)
Discussion started by: Neo
0 Replies
LEARN ABOUT ULTRIX
ntp.conf
ntp.conf(5) File Formats Manual ntp.conf(5)
Name
ntp.conf - Network Time Protocol configuration file
Description
The file is the configuration file for the Network Time Protocol (NTP) daemon, This file must be configured on your system before running
Any host names that you specify in the file must have an entry in the file, or an entry in the master database, if the database is being
served to your system by BIND/Hesiod or Yellow Pages.
The file has four entry formats:
trusting no
This entry guarantees that your system synchronizes only to the NTP servers identified in the peer and server entries specified. Dig-
ital recommends that all systems include the entry.
peer server
This entry identifies server as one of the NTP servers that your system trusts, and from which your system will accept time synchro-
nization. Your system may also provide time synchronization to this server. Servers can be identified by host name or internet
address.
NTP servers should be configured with entries.
server server
This entry identifies server as one of the NTP servers that your system trusts, and from which your system will accept time synchro-
nization. Your system can not provide time synchronization to this server. Servers can be identified by host name or internet
address.
NTP clients should be configured with entries.
peer /dev/null LOCL 1 -5 local
This entry identifies your system as a local reference clock. A local reference clock is the most accurate system clock available at
your site. If you receive time synchronization from the Internet NTP service, you should not include this entry on any of your sys-
tems. At most, one system in a set of nodes running should be identified as a local reference clock.
A host which specifies this entry should not specify any or entries.
Examples
This is a sample configuration file for an NTP client which receives time synchronization from the NTP servers: and Lines beginning with a
number sign (#) are comments.
#
# NTP Configuration File
# This file is mandatory for the ntpd daemon
#
#
#
# ** A L L **
#
# "trusting no" prevents this host from synchronizing
# to any host that is not listed below. It is recommended
# that all hosts include the line "trusting no".
#
trusting no
#
#
# ** S E R V E R **
#
# If you are configuring a server, use "peer" entries to
# synchronize to other NTP servers. For example, server1,
# server2, and server3.
#
#peer server1
#peer server2
#peer server3
#
#
#
#
# ** C L I E N T **
#
# If you are configuring a client, use "server" entries to
# synchronize to NTP servers. For example, server1, server2,
# and server3.
#
server server1
server server2
server server3
#
#
#
# ** L O C A L R E F E R E N C E C L O C K **
#
# If you are configuring a local reference clock, include the
# following entry and the "trusting no" entry ONLY.
#
#peer /dev/null LOCL 1 -5 local
#
See Also
ntp(1), ntpd(8), ntpdc(8)
RFC 1129--Internet time synchronization: The Network Time Protocol
Introduction to Networking and Distributed System Services
ntp.conf(5)