Thanks for wonderful explanation. Here is my current setup.
There are 6 x 1TB disks. I installed Solaris 11.4 on the first entire disk and then mirrored it in rpool with the second disk. That gives me 4 disks of 1 TB each.
When I login to OVM Manager, select "create repository", select this server, select "physical disks", it gives me 4 disks in below format to select from. Here I can choose any disk and create a repository
Hi all,
I would like to know how to make new partitions....
I currently have allocated 60G for various slices (I have totally used 4 out of 7 available slices...
I am running only solaris on my box.
My plan is to have entire disk dedicated to solaris and run other OS from within... (19 Replies)
I have to do this exercise:
Create a virtual disk
Partition this disk
Create File system
Mount File System
I'm using Minix (which runs by Qemu as guest machine) on Linux (Host)
Is there anybody who knows how to solve first three point? :confused:
Thanks (4 Replies)
Hi All,
does any body know how to create Virtual NIC in Solaris 10
if any one have good article or reference
kindly provide me
i try to Google
but i didn't find good one (7 Replies)
Hi,
I have installed oracle 10g release 2 on solaris 10 Zone. I want to configure ASM in local Zone using virtual disks in place of real disks.
I have configured ASM using virtual disks in place real disk in Solaris 10 Global zone. How i can do in local Zone
Kindly guid me with proper... (1 Reply)
Hi, my root pool is as follows. How can I create a metadb if I want to create SVM volumes?
zpool status
pool: rpool1
state: ONLINE
scan: none requested
config:
NAME STATE READ WRITE CKSUM
rpool1 ONLINE 0 0 0
c4t1d0s0 ... (10 Replies)
I’m setting up a boot disk mirror on Solaris 10 x86. I’m used to doing it on SPARC, where you can copy the partition table using fmthard. My x86 boot disk has 2 primary partitions, a Solaris one and a diagnostic one. Is there a way to copy those 2 primary partitions to the second disk without... (6 Replies)
Hi,
Quick question.
I have a data zpool that consists of 1 disk.
pool: data
state: ONLINE
scrub: none requested
config:
NAME STATE READ WRITE CKSUM
data ONLINE 0 0 0
c0t50002AC0014B06BEd0 ONLINE... (2 Replies)
have been trying to create a 2 GB ramdisk (virtual) to run on my T-2000 simulator (Legion) which has sun4v architecture. I have a SPARC workstation which runs on sun4u architecture with Solaris 10.
I have created a ramdisk image using dd command, newfs, then used ufsrestore to restore the... (3 Replies)
issue,
I had a zpool which was full
pool_temp1 199G 197G 1.56G 99% ONLINE -
pool_temp2 199G 196G 3.09G 98% ONLINE -
as you can see, full
so I replaced with a larger disk.
zpool replace pool_temp1 c3t600144F0FF8BA036000058CC1DB80008d0s0... (2 Replies)
Discussion started by: rrodgers
2 Replies
LEARN ABOUT HPUX
vxreattach
vxreattach(1M)vxreattach(1M)NAME
vxreattach - reattach disk drives that have once again become accessible
SYNOPSIS
/etc/vx/bin/vxreattach [-br ] [accessname...]
/etc/vx/bin/vxreattach -c accessname
DESCRIPTION
The vxreattach utility reattaches disks to the disk group they were in and retains the same media name.
This operation may be necessary if a disk has a transient failure, or if Veritas Volume Manager (VxVM) starts with some disk drivers
unloaded and unloadable. Disks then enter the failed state. If the problem is fixed, vxreattach may be able to reattach the disks without
plexes being flagged as stale, as long as the reattach happens before any volumes on the disk are started.
vxreattach tries to find a disk in the same disk group with the same disk ID for the disk(s) to be reattached. The reattach operation may
fail even after finding the disk with the matching disk ID if the original cause (or some other cause) for the disk failure still exists.
vxreattach is usually invoked by vxdiskadm when performing disk recovery. It is not intended to be run directly by an administrator.
OPTIONS -b Performs the reattach operation in the background.
-c Checks if a reattach is possible. No operation is performed, but the name of the disk group and disk media name at which the
disk can be reattached is displayed.
-r Tries to recover stale plexes of any volumes on the failed disk. It does this by calling vxrecover.
EXIT CODES
A zero exit status is returned if the reattach is performed; non-zero is returned otherwise.
See vxintro(1M) for a list of standard exit codes.
EXAMPLES
Check if reattachment of disk c1t2d0 is possible:
/etc/vx/bin/vxreattach -c c1t2d0
If reattachment is possible, vxreattach returns with an exit status of 0 and displays the disk group name and disk media name. If reat-
tachment is not possible, vxreattach returns an exit status of 2 and displays an error.
Attempt to reattach the disk in the foreground and try to recover stale plexes of any volumes on the disk:
/etc/vx/bin/vxreattach -r c1t2d0
If the reattachment is successful, vxreattach returns an exit status of 0. Otherwise, if an error occurs, vxreattach returns a non-zero
exit code as defined on vxintro(1M).
FILES
/etc/default/vxplex Standard defaults file that can be used to determine whether FastResync is used when attaching plexes. See vxplex(1M)
for details.
SEE ALSO vxdiskadm(1M), vxintro(1M), vxplex(1M), vxrecover(1M)VxVM 5.0.31.1 24 Mar 2008 vxreattach(1M)