Thanks for wonderful explanation. Here is my current setup.
There are 6 x 1TB disks. I installed Solaris 11.4 on the first entire disk and then mirrored it in rpool with the second disk. That gives me 4 disks of 1 TB each.
When I login to OVM Manager, select "create repository", select this server, select "physical disks", it gives me 4 disks in below format to select from. Here I can choose any disk and create a repository
Hi all,
I would like to know how to make new partitions....
I currently have allocated 60G for various slices (I have totally used 4 out of 7 available slices...
I am running only solaris on my box.
My plan is to have entire disk dedicated to solaris and run other OS from within... (19 Replies)
I have to do this exercise:
Create a virtual disk
Partition this disk
Create File system
Mount File System
I'm using Minix (which runs by Qemu as guest machine) on Linux (Host)
Is there anybody who knows how to solve first three point? :confused:
Thanks (4 Replies)
Hi All,
does any body know how to create Virtual NIC in Solaris 10
if any one have good article or reference
kindly provide me
i try to Google
but i didn't find good one (7 Replies)
Hi,
I have installed oracle 10g release 2 on solaris 10 Zone. I want to configure ASM in local Zone using virtual disks in place of real disks.
I have configured ASM using virtual disks in place real disk in Solaris 10 Global zone. How i can do in local Zone
Kindly guid me with proper... (1 Reply)
Hi, my root pool is as follows. How can I create a metadb if I want to create SVM volumes?
zpool status
pool: rpool1
state: ONLINE
scan: none requested
config:
NAME STATE READ WRITE CKSUM
rpool1 ONLINE 0 0 0
c4t1d0s0 ... (10 Replies)
I’m setting up a boot disk mirror on Solaris 10 x86. I’m used to doing it on SPARC, where you can copy the partition table using fmthard. My x86 boot disk has 2 primary partitions, a Solaris one and a diagnostic one. Is there a way to copy those 2 primary partitions to the second disk without... (6 Replies)
Hi,
Quick question.
I have a data zpool that consists of 1 disk.
pool: data
state: ONLINE
scrub: none requested
config:
NAME STATE READ WRITE CKSUM
data ONLINE 0 0 0
c0t50002AC0014B06BEd0 ONLINE... (2 Replies)
have been trying to create a 2 GB ramdisk (virtual) to run on my T-2000 simulator (Legion) which has sun4v architecture. I have a SPARC workstation which runs on sun4u architecture with Solaris 10.
I have created a ramdisk image using dd command, newfs, then used ufsrestore to restore the... (3 Replies)
issue,
I had a zpool which was full
pool_temp1 199G 197G 1.56G 99% ONLINE -
pool_temp2 199G 196G 3.09G 98% ONLINE -
as you can see, full
so I replaced with a larger disk.
zpool replace pool_temp1 c3t600144F0FF8BA036000058CC1DB80008d0s0... (2 Replies)
Discussion started by: rrodgers
2 Replies
LEARN ABOUT SUNOS
metaimport
metaimport(1M)metaimport(1M)NAME
metaimport - imports disk sets into existing Solaris Volume Manager configurations
SYNOPSIS
metaimport -s setname [-n] [-v] [-f] [disks...]
metaimport -r [disks...]
metaimport -V
metaimport -?
The metaimport command allows the importing of disk sets, including replicated disk sets, into an existing Solaris Volume Manager configu-
ration. Replicated disk sets are disk sets created using remote replication software.
The default Solaris Volume Manager configuration specifies a maximum number of disk sets that can be configured. The metaimport command
fails if importing the disk set would result in exceeding the number of disk sets configured on the system. To increase the number of disk
sets allowed on a system, see the .
Use metaset(1M) or metastat(1M) to view the configuration of the imported set.
You must run metaimport as root.
metaimport requires a functional Solaris Volume Manager configuration before it runs.
The following options are supported:
-f Force the import, even if a quorum of replicas from the imported disk set is not available. This option could
result in corrupt configurations and should only be used when metaimport fails with the "Insufficient quorum
detected; exiting" error. If only a partial disk set is available, this option might be necessary to successfully
import. Some or all data could be corrupted or unavailable when importing a partial set or a set lacking a replica
quorum.
-n Does not actually perform the operation, but shows the output or errors that would have resulted from the opera-
tion, had it been run.
-r Report on the non-configured disk sets found on the system. If no disk device or LUN is specified, metaimport
reports on all non-configured disk sets attached to the system. When the name of one disk is specified, metaimport
reports on the disk set (or virtual LUN) containing the specified disk. If two or more disks are specified, metaim-
port reports on the set (or sets, if they belong to different disk sets) containing the specified disks. If two or
more disks are specified, metaimport reports on the set (or sets, if they belong to different disk sets) containing
the specified disks.
-s setname Specify the disk set name to use when importing. The imported disk set will be called setname, without regard to
the name it may have had on a different system.
-v Verbose. Provides detailed information about the metadb replica location and status.
-V Version information.
-? Display a help message.
Example 1: Importing a Disk Set
The following example creates a disk set called blue and identifies c1t5d0 as a disk containing a state database replica from the disk set
being imported.
# metaimport -s blue c1t5d0
Example 2: Reporting Disk Sets to Import
The following example scans all disks and LUNs attached to the system and configured as part of the system. It scans for disks that could
be part of a disk set to be imported. Components that are already part of the Solaris Volume Manager configuration are ignored.
This use of metaimport provides suggested forms of the metaimport command to use to actually import the disk sets that have been found. You
can specify a component on the command line to reduce the scope of the scan and generate results more quickly.
# metaimport -r
0 Successful completion.
>0 An error occurred.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWmdu |
+-----------------------------+-----------------------------+
|Interface Stability |Stable |
+-----------------------------+-----------------------------+
mdmonitord(1M), metaclear(1M), metadb(1M), metadetach(1M), metahs(1M), metainit(1M), metaoffline(1M), metaonline(1M), metaparam(1M),
metarecover(1M), metareplace(1M), metaroot(1M), metaset(1M), metasync(1M), metattach(1M), md.tab(4), md.cf(4), mddb.cf(4), attributes(5)
16 May 2005 metaimport(1M)