Sponsored Content
Operating Systems Solaris Solaris 11 link aggregation with multiple VLANs - not working Post 303045089 by solaris_1977 on Wednesday 11th of March 2020 06:54:26 PM
Old 03-11-2020
I was able to figure it out and able to configure. Thanks for the help
 

9 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

3. AIX

Link aggregation with hacmp ?

Hi, I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies

4. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

5. IP Networking

Interface bonding / Link aggregation (Multiple)

Hello, I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave. Example: eth0 RX 123.2 GiB TX 22.5 GiB eth1 RX 84.8 GiB TX 8.3 GiB eth2... (3 Replies)
Discussion started by: TehOne
3 Replies

6. Solaris

solaris link aggregation problem , once i reboot it is not showing, not able to ping the default gat

Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1 after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies

7. Solaris

Link aggregation issues Solaris 10

I have setup link aggregation with 3 interfaces on my solaris 10 system. All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links. bash-4.3# dladm show-aggr -s key:33 ipackets rbytes opackets obytes %ipkts %opkts ... (3 Replies)
Discussion started by: primeaup
3 Replies

8. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

9. Solaris

Solaris link aggregation not working as expected

Hi, This is Solaris-10 x86 platform. I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise. # netstat -nr Routing Table: IPv4 Destination Gateway Flags Ref Use Interface --------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
HTML::Microformats::Format::figure(3pm) 		User Contributed Perl Documentation		   HTML::Microformats::Format::figure(3pm)

NAME
HTML::Microformats::Format::figure - the figure microformat SYNOPSIS
use HTML::Microformats::DocumentContext; use HTML::Microformats::Format::figure; use Scalar::Util qw(blessed); my $context = HTML::Microformats::DocumentContext->new($dom, $uri); my @objects = HTML::Microformats::Format::figure->extract_all( $dom->documentElement, $context); foreach my $fig (@objects) { printf("<%s> %s ", $fig->get_image, $fig->get_legend->[0]); foreach my $maker ($p->get_credit) { if (blessed($maker)) { printf(" - by %s ", $maker->get_fn); } else { printf(" - by %s ", $maker); } } } DESCRIPTION
HTML::Microformats::Format::figure inherits from HTML::Microformats::Format. See the base class definition for a description of property getter/setter methods, constructors, etc. MICROFORMAT
HTML::Microformats::Format::figure supports figure as described at <http://microformats.org/wiki/figure>. RDF OUTPUT
Data is returned using Dublin Core and FOAF. BUGS
Please report any bugs to <http://rt.cpan.org/>. SEE ALSO
HTML::Microformats::Format, HTML::Microformats. AUTHOR
Toby Inkster <tobyink@cpan.org>. COPYRIGHT
Copyright 2008-2011 Toby Inkster This library is free software; you can redistribute it and/or modify it under the same terms as Perl itself. DISCLAIMER OF WARRANTIES
THIS PACKAGE IS PROVIDED "AS IS" AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. perl v5.14.2 2011-12-06 HTML::Microformats::Format::figure(3pm)
All times are GMT -4. The time now is 10:47 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy