|
|
Sponsored Content
Operating Systems
Solaris
Solaris 11 link aggregation with multiple VLANs - not working
Post 303045089 by solaris_1977 on Wednesday 11th of March 2020 06:54:26 PM
03-11-2020
|
|
9 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
4. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
5. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
6. Solaris
solaris link aggregation problem , once i reboot it is not showing, not able to ping the default gat
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies
7. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
8. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
9. Solaris
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
LEARN ABOUT SUNOS
install-solaris
install-solaris(1M) install-solaris(1M) NAME
install-solaris - install the Solaris operating system SYNOPSIS
install-solaris install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation, install-solaris invokes either a text-based installer or a graphical installer. The following minimum requirements for physical memory dictate which features are available during installation: For SPARC machines: 128 MB Minimum physical memory for all installation types 128 MB Minimum physical memory required for windowing system 384 MB Minimum physical memory required for graphical-based installation For x86 machines: 256 MB Minimum physical memory for all installation types 256 MB Minimum physical memory required for windowing system 512 MB Minimum physical memory required for graphical-based installation In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea- tures available. install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more details. install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the installation media. Refer to the for disk space requirements. Refer to the for more information on the various menus and selections. See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcdrom (Solaris instal- | | |lation media) | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ pkginfo(1), install(1M), pkgadd(1M), attributes(5) It is advisable to exit install-solaris by means of the exit options in the install-solaris menus. 23 Sep 2005 install-solaris(1M)