03-11-2020
I was able to figure it out and able to configure. Thanks for the help
9 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
4. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
5. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
6. Solaris
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies
7. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
8. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
9. Solaris
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
LEARN ABOUT DEBIAN
fipvlan
FIPVLAN(8) Open-FCoE Tools FIPVLAN(8)
NAME
fipvlan - Fibre Channel over Ethernet VLAN Discovery
SYNOPSIS
fipvlan [-c|--create] [-s|--start] interfaces
fipvlan -a|--auto [-c|--create] [-d|--debug] [-s|--start] [-l|--link-retry <num>]
fipvlan -h|--help
fipvlan -v|--version
DESCRIPTION
The fipvlan command performs Fibre Channel over Ethernet (FCoE) Initialization Protocol (FIP) VLAN Discovery over Ethernet interfaces.
fipvlan can be used as a diagnostic tool to determine which VLANs have FCoE services available on a network, prior to configuring VLAN
interfaces and the Open-FCoE initiator. fipvlan can also be used to create VLAN interfaces as they are discovered, and to start the
Open-FCoE initiator. The --create and --start options are primarily intended to be used as part of an Open-FCoE boot solution. FCoE
instances started in this way cannot be destroyed or reset by fcoeadm.
fipvlan takes a list of network interface names to run the VLAN discovery protocol over, or the --auto option to use all available Ethernet
interfaces.
fipvlan will enable any interface which is found to be not enabled by the time the program runs. If no response is received on that
interface it will be shutdown again when fipvlan terminates.
OPTIONS
-a, --auto
Use all Ethernet interfaces currently available
-c, --create
Create network interfaces for discovered FCoE VLANs. If a VLAN device already exists for a discovered VLAN, a new VLAN device will not
be created.
-d, --debug
Enable debugging output
-s, --start
Start the Open-FCoE initiator on discovered FCoE VLANs
-f, --suffix <suffix string>
Append the specified string <suffix string> to VLAN interface names.
-l, --link-retry <number of retries>
Retry check for link up up to <number of retries> times. The link state is retried every 500 ms. The default is 20.
-h, --help
Display a help message with basic usage instructions
-v, --version
Display the fipvlan version string
VLAN NAMING CONVENTIONS
The default VLAN device name is dev.vlan; where dev is the name of the Ethernet parent device and vlan is the discovered VLAN ID number. An
optional suffix can be appended to this with -f commandline option.
EXAMPLES
Display all discoverable VLANs with FCoE services
fipvlan --auto
Discover FCoE VLANs on interface eth2, create VLAN devices and start the Open-FCoE initiator
fipvlan --create --start eth2
In this example if FCoE services were available on VLAN 101 of network interface eth2, then a VLAN interface eth2.101-fcoe would be created
and used as the parent device for the initiator.
SEE ALSO
fcoeadm(8) fcoemon(8)
SUPPORT
fipvlan is part of the fcoe-utils package, maintained through the Open-FCoE project. Resources for both developers and users can be found
at the Open-FCoE website http://open-fcoe.org/
Open-FCoE 10/06/2011 FIPVLAN(8)