Sponsored Content
Operating Systems Solaris Solaris 11 link aggregation with multiple VLANs - not working Post 303044847 by Peasant on Thursday 5th of March 2020 05:29:16 AM
Old 03-05-2020
On aggr0 you can only define IP address from native VLAN on those ports.
If you wish to define a tagged IP on the hypervisor, you need to create vlan interface, then define IP on that.

If you wish to use the interface for virtual machines, you define a VSW with aggr0 link.
Then you add a vnet via ldm command using that VSW.

You can have both on the hypervisor, vlan interfaces and VSW above aggr0, but of course with different IP addresses (vm and hypervisor).
I would recommend reading about Oracle VM server for SPARC and a bit about networking as well
Looks like you are mixing hypervisor and vm part regarding network.

Regards
Peasant.
These 2 Users Gave Thanks to Peasant For This Post:
 

9 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

3. AIX

Link aggregation with hacmp ?

Hi, I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies

4. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

5. IP Networking

Interface bonding / Link aggregation (Multiple)

Hello, I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave. Example: eth0 RX 123.2 GiB TX 22.5 GiB eth1 RX 84.8 GiB TX 8.3 GiB eth2... (3 Replies)
Discussion started by: TehOne
3 Replies

6. Solaris

solaris link aggregation problem , once i reboot it is not showing, not able to ping the default gat

Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1 after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies

7. Solaris

Link aggregation issues Solaris 10

I have setup link aggregation with 3 interfaces on my solaris 10 system. All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links. bash-4.3# dladm show-aggr -s key:33 ipackets rbytes opackets obytes %ipkts %opkts ... (3 Replies)
Discussion started by: primeaup
3 Replies

8. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

9. Solaris

Solaris link aggregation not working as expected

Hi, This is Solaris-10 x86 platform. I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise. # netstat -nr Routing Table: IPv4 Destination Gateway Flags Ref Use Interface --------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
AGGREGATE_INFO(3)							 1							 AGGREGATE_INFO(3)

aggregate_info - Gets aggregation information for a given object

SYNOPSIS
array aggregate_info (object $object) DESCRIPTION
Gets the aggregation information for the given $object. PARAMETERS
o $object - RETURN VALUES
Returns the aggregation information as an associative array of arrays of methods and properties. The key for the main array is the name of the aggregated class. EXAMPLES
Example #1 Using aggregate_info(3) <?php class Slicer { var $vegetable; function Slicer($vegetable) { $this->vegetable = $vegetable; } function slice_it($num_cuts) { echo "Doing some simple slicing "; for ($i=0; $i < $num_cuts; $i++) { // do some slicing } } } class Dicer { var $vegetable; var $rotation_angle = 90; // degrees function Dicer($vegetable) { $this->vegetable = $vegetable; } function dice_it($num_cuts) { echo "Cutting in one direction "; for ($i=0; $i < $num_cuts; $i++) { // do some cutting } $this->rotate($this->rotation_angle); echo "Cutting in a second direction "; for ($i=0; $i < $num_cuts; $i++) { // do some more cutting } } function rotate($deg) { echo "Now rotating {$this->vegetable} {$deg} degrees "; } function _secret_super_dicing($num_cuts) { // so secret we cannot show you ;-) } } $obj = new Slicer('onion'); aggregate($obj, 'Dicer'); print_r(aggregate_info($obj)); ?> The above example will output: Array ( [dicer] => Array ( [methods] => Array ( [0] => dice_it [1] => rotate ) [properties] => Array ( [0] => rotation_angle ) ) ) As you can see, all properties and methods of the Dicer class have been aggregated into our new object, with the exception of the class constructor and the method _secret_super_dicing SEE ALSO
aggregate(3), aggregate_methods(3), aggregate_methods_by_list(3), aggregate_methods_by_regexp(3), aggregate_properties(3), aggregate_prop- erties_by_list(3), aggregate_properties_by_regexp(3), deaggregate(3). PHP Documentation Group AGGREGATE_INFO(3)
All times are GMT -4. The time now is 08:39 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy