Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Solaris 11 link aggregation with multiple VLANs - not working
Operating Systems Solaris Solaris 11 link aggregation with multiple VLANs - not working Post 303044837 by solaris_1977 on Thursday 5th of March 2020 12:16:52 AM
Old 03-05-2020
Solaris 11 link aggregation - not working - can't ping gateway
This link was helpful and I got the idea that vlanNUM would be created on OVM/hypervisor level.
I deleted VLAN interfaces, recreated aggr0 with net0 and net7. But I can't ping its gateway. I can see packets incoming from two VLANs, if I snoop on net0, net7 and aggr0.
Per network guys, their side configurations are okay, but I will check again if my configurations are looking okay.
Code:
root@ovmi-host1:~# netstat -nrv | grep default
default              0.0.0.0         192.168.244.129                 0   2 UG       0      0
root@ovmi-host1:~# ping 192.168.244.129
no answer from 192.168.244.129
root@ovmi-host1:~# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
        inet 127.0.0.1 netmask ff000000
sp-phys0: flags=100001000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4,PHYSRUNNING> mtu 1500 index 2
        inet 169.254.182.77 netmask ffffff00 broadcast 169.254.182.255
        ether 2:21:28:57:47:17
aggr0: flags=100001000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4,PHYSRUNNING> mtu 1500 index 3
        inet 192.168.244.161 netmask ffffffc0 broadcast 192.168.244.191
        ether 0:10:e0:e2:dc:8c
lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
        inet6 ::1/128
sp-phys0: flags=120002000840<RUNNING,MULTICAST,IPv6,PHYSRUNNING> mtu 1500 index 2
        inet6 ::/0
        ether 2:21:28:57:47:17
aggr0: flags=120002000840<RUNNING,MULTICAST,IPv6,PHYSRUNNING> mtu 1500 index 3
        inet6 ::/0
        ether 0:10:e0:e2:dc:8c
root@ovmi-host1:~#
root@ovmi-host1:~# dladm show-phys | grep up
net0            Ethernet      up         1000   full      i40e0
net1            Ethernet      up         1000   full      i40e1
net7            Ethernet      up         1000   full      igb3
net16           Ethernet      up         1000   full      vsw0
sp-phys0        Ethernet      up         10     full      usbecm2
root@ovmi-host1:~# dladm show-aggr -x
LINK       PORT           SPEED DUPLEX   STATE     ADDRESS            PORTSTATE
aggr0      --             1000Mb full    up        0:10:e0:e2:dc:8c   --
           net0           1000Mb full    up        0:10:e0:e2:dc:8c   attached
           net7           1000Mb full    up        b4:96:91:4c:ae:93  attached
root@ovmi-host1:~# dladm show-aggr -L
LINK                PORT         AGGREGATABLE SYNC COLL DIST DEFAULTED EXPIRED
aggr0               net0         yes          yes  yes  yes  no        no
--                  net7         yes          yes  yes  yes  no        no
root@ovmi-host1:~#
root@ovmi-host1:~# dladm show-link | grep up
aggr0               aggr      1500   up       net0 net7
net0                phys      1500   up       --
net1                phys      1500   up       --
net7                phys      1500   up       --
net16               phys      1500   up       --
sp-phys0            phys      1500   up       --
root@ovmi-host1:~#

Am I missing something in this config ?
Last edited by solaris_1977; 03-05-2020 at 02:03 AM.. Reason: Corrected title
 

9 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

3. AIX

Link aggregation with hacmp ?

Hi, I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies

4. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

5. IP Networking

Interface bonding / Link aggregation (Multiple)

Hello, I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave. Example: eth0 RX 123.2 GiB TX 22.5 GiB eth1 RX 84.8 GiB TX 8.3 GiB eth2... (3 Replies)
Discussion started by: TehOne
3 Replies

6. Solaris

solaris link aggregation problem , once i reboot it is not showing, not able to ping the default gat

Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1 after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies

7. Solaris

Link aggregation issues Solaris 10

I have setup link aggregation with 3 interfaces on my solaris 10 system. All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links. bash-4.3# dladm show-aggr -s key:33 ipackets rbytes opackets obytes %ipkts %opkts ... (3 Replies)
Discussion started by: primeaup
3 Replies

8. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

9. Solaris

Solaris link aggregation not working as expected

Hi, This is Solaris-10 x86 platform. I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise. # netstat -nr Routing Table: IPv4 Destination Gateway Flags Ref Use Interface --------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies

LEARN ABOUT CENTOS

enum_ieee80211_ampdu_mlme_action

ENUM 
IEEE80211_AMPDU(9) 				     Advanced driver interface					   ENUM IEEE80211_AMPDU(9)

NAME

       enum_ieee80211_ampdu_mlme_action - A-MPDU actions

SYNOPSIS

       enum ieee80211_ampdu_mlme_action {
	 IEEE80211_AMPDU_RX_START,
	 IEEE80211_AMPDU_RX_STOP,
	 IEEE80211_AMPDU_TX_START,
	 IEEE80211_AMPDU_TX_STOP_CONT,
	 IEEE80211_AMPDU_TX_STOP_FLUSH,
	 IEEE80211_AMPDU_TX_STOP_FLUSH_CONT,
	 IEEE80211_AMPDU_TX_OPERATIONAL
       };

CONSTANTS

       IEEE80211_AMPDU_RX_START
	   start RX aggregation

       IEEE80211_AMPDU_RX_STOP
	   stop RX aggregation

       IEEE80211_AMPDU_TX_START
	   start TX aggregation

       IEEE80211_AMPDU_TX_STOP_CONT
	   stop TX aggregation but continue transmitting queued packets, now unaggregated. After all packets are transmitted the driver has to
	   call ieee80211_stop_tx_ba_cb_irqsafe.

       IEEE80211_AMPDU_TX_STOP_FLUSH
	   stop TX aggregation and flush all packets, called when the station is removed. There's no need or reason to call
	   ieee80211_stop_tx_ba_cb_irqsafe in this case as mac80211 assumes the session is gone and removes the station.

       IEEE80211_AMPDU_TX_STOP_FLUSH_CONT
	   called when TX aggregation is stopped but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe yet and now the connection is
	   dropped and the station will be removed. Drivers should clean up and drop remaining packets when this is called.

       IEEE80211_AMPDU_TX_OPERATIONAL
	   TX aggregation has become operational

DESCRIPTION

       These flags are used with the ampdu_action callback in struct ieee80211_ops to indicate which action is needed.

       Note that drivers MUST be able to deal with a TX aggregation session being stopped even before they OK'ed starting it by calling
       ieee80211_start_tx_ba_cb_irqsafe, because the peer might receive the addBA frame and send a delBA right away!

AUTHOR

       Johannes Berg <johannes@sipsolutions.net>
	   Author.

COPYRIGHT

Kernel Hackers Manual 3.10					     June 2014						   ENUM IEEE80211_AMPDU(9)
All times are GMT -4. The time now is 06:24 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy