Solaris 11 link aggregation - not working - can't ping gateway
This link was helpful and I got the idea that vlanNUM would be created on OVM/hypervisor level.
I deleted VLAN interfaces, recreated aggr0 with net0 and net7. But I can't ping its gateway. I can see packets incoming from two VLANs, if I snoop on net0, net7 and aggr0.
Per network guys, their side configurations are okay, but I will check again if my configurations are looking okay.
Am I missing something in this config ?
Last edited by solaris_1977; 03-05-2020 at 02:03 AM..
Reason: Corrected title
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
LEARN ABOUT PHP
aggregate_info
AGGREGATE_INFO(3) 1 AGGREGATE_INFO(3)aggregate_info - Gets aggregation information for a given objectSYNOPSIS
array aggregate_info (object $object)
DESCRIPTION
Gets the aggregation information for the given $object.
PARAMETERS
o $object
-
RETURN VALUES
Returns the aggregation information as an associative array of arrays of methods and properties. The key for the main array is the name of
the aggregated class.
EXAMPLES
Example #1
Using aggregate_info(3)
<?php
class Slicer {
var $vegetable;
function Slicer($vegetable)
{
$this->vegetable = $vegetable;
}
function slice_it($num_cuts)
{
echo "Doing some simple slicing
";
for ($i=0; $i < $num_cuts; $i++) {
// do some slicing
}
}
}
class Dicer {
var $vegetable;
var $rotation_angle = 90; // degrees
function Dicer($vegetable)
{
$this->vegetable = $vegetable;
}
function dice_it($num_cuts)
{
echo "Cutting in one direction
";
for ($i=0; $i < $num_cuts; $i++) {
// do some cutting
}
$this->rotate($this->rotation_angle);
echo "Cutting in a second direction
";
for ($i=0; $i < $num_cuts; $i++) {
// do some more cutting
}
}
function rotate($deg)
{
echo "Now rotating {$this->vegetable} {$deg} degrees
";
}
function _secret_super_dicing($num_cuts)
{
// so secret we cannot show you ;-)
}
}
$obj = new Slicer('onion');
aggregate($obj, 'Dicer');
print_r(aggregate_info($obj));
?>
The above example will output:
Array
(
[dicer] => Array
(
[methods] => Array
(
[0] => dice_it
[1] => rotate
)
[properties] => Array
(
[0] => rotation_angle
)
)
)
As you can see, all properties and methods of the Dicer class have been aggregated into our new object, with the exception of the class
constructor and the method _secret_super_dicing
SEE ALSO aggregate(3), aggregate_methods(3), aggregate_methods_by_list(3), aggregate_methods_by_regexp(3), aggregate_properties(3), aggregate_prop-
erties_by_list(3), aggregate_properties_by_regexp(3), deaggregate(3).
PHP Documentation Group AGGREGATE_INFO(3)