Sponsored Content
Operating Systems Solaris Solaris 11 link aggregation with multiple VLANs - not working Post 303044836 by Peasant on Wednesday 4th of March 2020 11:24:56 PM
Old 03-05-2020
You will then create a vsw (virtual switch) on top of aggr0
Then using that vsw add interfaces to VMs.

There is no need to create vlanNUM interfaces on the hypervisor in that case.
You only define vlan interfaces on hypervisor if you wish to define IP for the hypervisor itself.

Check out this post :
LDOM Solaris 11 add Network vsw (Virtual switch)

Hope that helps
Regards
Peasant.
 

9 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

3. AIX

Link aggregation with hacmp ?

Hi, I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies

4. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

5. IP Networking

Interface bonding / Link aggregation (Multiple)

Hello, I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave. Example: eth0 RX 123.2 GiB TX 22.5 GiB eth1 RX 84.8 GiB TX 8.3 GiB eth2... (3 Replies)
Discussion started by: TehOne
3 Replies

6. Solaris

solaris link aggregation problem , once i reboot it is not showing, not able to ping the default gat

Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1 after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies

7. Solaris

Link aggregation issues Solaris 10

I have setup link aggregation with 3 interfaces on my solaris 10 system. All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links. bash-4.3# dladm show-aggr -s key:33 ipackets rbytes opackets obytes %ipkts %opkts ... (3 Replies)
Discussion started by: primeaup
3 Replies

8. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

9. Solaris

Solaris link aggregation not working as expected

Hi, This is Solaris-10 x86 platform. I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise. # netstat -nr Routing Table: IPv4 Destination Gateway Flags Ref Use Interface --------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
EPAIR(4)                                                   BSD Kernel Interfaces Manual                                                   EPAIR(4)

NAME
epair -- A pair of virtual back-to-back connected Ethernet interfaces. SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file: device epair Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_epair_load="YES" DESCRIPTION
The epair is a pair of Ethernet-like software interfaces, which are connected back-to-back with a virtual cross-over cable. Each epair interface pair is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf(5). While for cloning you only give either epair or epair<n> the epair pair will be named like epair<n>[ab]. This means the names of the first epair interfaces will be epair0a and epair0b. Like any other Ethernet interface, an epair needs to have a network address. Each epair will be assigned a locally administered address by default, that is only guaranteed to be unique within one network stack. To change the default addresses one may use the SIOCSIFADDR ioctl(2) or ifconfig(8) utility. The basic intend is to provide connectivity between two virtual network stack instances. When connected to a if_bridge(4) one end of the interface pair can also be part of another (virtual) LAN. As with any other Ethernet interface one can configure vlan(4) support on top of it. SEE ALSO
ioctl(2), altq(4), bpf(4), if_bridge(4), vlan(4), loader.conf(5,) rc.conf(5), ifconfig(8) HISTORY
The epair interface first appeared in FreeBSD 8.0. AUTHORS
The epair interface was written by Bjoern A. Zeeb, CK Software GmbH, under sponsorship from the FreeBSD Foundation. BSD July 26, 2009 BSD
All times are GMT -4. The time now is 09:34 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy