03-05-2020
You will then create a vsw (virtual switch) on top of
aggr0
Then using that vsw add interfaces to VMs.
There is no need to create
vlanNUM interfaces on the hypervisor in that case.
You only define vlan interfaces on hypervisor if you wish to define IP for the hypervisor itself.
Check out this post :
LDOM Solaris 11 add Network vsw (Virtual switch)
Hope that helps
Regards
Peasant.
9 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
4. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
5. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
6. Solaris
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies
7. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
8. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
9. Solaris
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
LEARN ABOUT FREEBSD
hv_vmbus
HYPER-V(4) BSD Kernel Interfaces Manual HYPER-V(4)
NAME
hv_vmbus -- Hyper-V Virtual Machine Bus (VMBus) Driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in the system kernel configuration file:
device hyperv
DESCRIPTION
The hv_vmbus provides a high performance communication interface between guest and root partitions in Hyper-V. Hyper-V is a hypervisor-based
virtualization technology from Microsoft. Hyper-V supports isolation in terms of a partition. A partition is a logical unit of isolation,
supported by the hypervisor, in which operating systems execute.
The Microsoft hypervisor must have at least one parent, or root, partition, running Windows Server operating system. The virtualization
stack runs in the parent partition and has direct access to the hardware devices. The root partition then creates the child partitions which
host the guest operating systems.
Child partitions do not have direct access to other hardware resources and are presented a virtual view of the resources, as virtual devices
(VDevs). Requests to the virtual devices are redirected either via the VMBus or the hypervisor to the devices in the parent partition, which
handles the requests.
The VMBus is a logical inter-partition communication channel. The parent partition hosts Virtualization Service Providers (VSPs) which com-
municate over the VMBus to handle device access requests from child partitions. Child partitions host Virtualization Service Consumers
(VSCs) which redirect device requests to VSPs in the parent partition via the VMBus. The Hyper-V VMBus driver defines and implements the
interface that facilitate high performance bi-directional communication between the VSCs and VSPs. All VSCs utilize the VMBus driver.
SEE ALSO
hv_ata_pci_disengage(4), hv_netvsc(4), hv_storvsc(4), hv_utils(4)
HISTORY
Support for hv_vmbus first appeared in FreeBSD 10.0. The driver was developed through a joint effort between Citrix Incorporated, Microsoft
Corporation, and Network Appliance Incorporated.
AUTHORS
FreeBSD support for hv_vmbus was first added by Microsoft BSD Integration Services Team <bsdic@microsoft.com>.
BSD
September 10, 2013 BSD