You do not define IP address of tagged VLAN on aggr0.
In your case you should :
Delete the address
Define the above address on VLAN interface vlan2170
Try pinging the gateway then.
Only native VLAN (untagged) will work on aggr0, while others such as 2170 will work on vlan2170 interface.
Those vlanNUM interfaces are the ones you configure IP address on for tagged VLAN(s) you created with dladm create-vlan ... over aggr0
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
LEARN ABOUT CENTOS
enum_ieee80211_ampdu_mlme_action
ENUM IEEE80211_AMPDU(9) Advanced driver interface ENUM IEEE80211_AMPDU(9)NAME
enum_ieee80211_ampdu_mlme_action - A-MPDU actions
SYNOPSIS
enum ieee80211_ampdu_mlme_action {
IEEE80211_AMPDU_RX_START,
IEEE80211_AMPDU_RX_STOP,
IEEE80211_AMPDU_TX_START,
IEEE80211_AMPDU_TX_STOP_CONT,
IEEE80211_AMPDU_TX_STOP_FLUSH,
IEEE80211_AMPDU_TX_STOP_FLUSH_CONT,
IEEE80211_AMPDU_TX_OPERATIONAL
};
CONSTANTS
IEEE80211_AMPDU_RX_START
start RX aggregation
IEEE80211_AMPDU_RX_STOP
stop RX aggregation
IEEE80211_AMPDU_TX_START
start TX aggregation
IEEE80211_AMPDU_TX_STOP_CONT
stop TX aggregation but continue transmitting queued packets, now unaggregated. After all packets are transmitted the driver has to
call ieee80211_stop_tx_ba_cb_irqsafe.
IEEE80211_AMPDU_TX_STOP_FLUSH
stop TX aggregation and flush all packets, called when the station is removed. There's no need or reason to call
ieee80211_stop_tx_ba_cb_irqsafe in this case as mac80211 assumes the session is gone and removes the station.
IEEE80211_AMPDU_TX_STOP_FLUSH_CONT
called when TX aggregation is stopped but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe yet and now the connection is
dropped and the station will be removed. Drivers should clean up and drop remaining packets when this is called.
IEEE80211_AMPDU_TX_OPERATIONAL
TX aggregation has become operational
DESCRIPTION
These flags are used with the ampdu_action callback in struct ieee80211_ops to indicate which action is needed.
Note that drivers MUST be able to deal with a TX aggregation session being stopped even before they OK'ed starting it by calling
ieee80211_start_tx_ba_cb_irqsafe, because the peer might receive the addBA frame and send a delBA right away!
AUTHOR
Johannes Berg <johannes@sipsolutions.net>
Author.
COPYRIGHT Kernel Hackers Manual 3.10 June 2014 ENUM IEEE80211_AMPDU(9)