You do not define IP address of tagged VLAN on aggr0.
In your case you should :
Delete the address
Define the above address on VLAN interface vlan2170
Try pinging the gateway then.
Only native VLAN (untagged) will work on aggr0, while others such as 2170 will work on vlan2170 interface.
Those vlanNUM interfaces are the ones you configure IP address on for tagged VLAN(s) you created with dladm create-vlan ... over aggr0
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
LEARN ABOUT NETBSD
agr
AGR(4) BSD Kernel Interfaces Manual AGR(4)NAME
agr -- link aggregation pseudo network interface driver
SYNOPSIS
pseudo-device agr
DESCRIPTION
The agr driver provides link aggregation functionality (a.k.a. L2 trunking or bonding).
It supports the IEEE 802.3ad Link Aggregation Control Protocol (LACP) and the Marker Protocol.
The agr driver supports the following link specific flags for ifconfig(8):
link0 Use the round-robin distribution algorithm. Don't use it unless you're really sure, because it violates the frame ordering rule.
-link0 Use the default distribution algorithm, which is based on the hash of DA/SA, TCI, and, if available, some upper layer protocol infor-
mation like ip(4) DA/SA.
link1 Disable LACP. Prevents any LACP or Marker messaging which leaves the ports in the default static configuration. Set this prior to
adding ports.
EXAMPLES
Create an agr interface, agr0, and attach re0 and re1 to it. In other words, aggregate re0 and re1 so that they can be used as a single
interface, agr0. The physical interfaces which are attached to the agr interface must not have any IP addresses, neither IPv4 nor IPv6.
ifconfig re0 inet xxx.xxx.xxx.xxx delete
ifconfig re0 inet6 fe80::xxxx:xxxx:xxxx:xxxx delete
ifconfig re1 inet xxx.xxx.xxx.xxx delete
ifconfig re1 inet6 fe80::xxxx:xxxx:xxxx:xxxx delete
ifconfig agr0 create
ifconfig agr0 agrport re0
ifconfig agr0 agrport re1
Destroy an interface created in the above example.
ifconfig agr0 -agrport re0
ifconfig agr0 -agrport re1
ifconfig agr0 destroy
SEE ALSO ifconfig(8)STANDARDS
IEEE 802.3ad Aggregation of Multiple Link Segments
HISTORY
The agr driver first appeared in NetBSD 4.0.
AUTHORS
The agr driver was written by YAMAMOTO Takashi.
BUGS
There is no way to configure LACP administrative variables, including system and port priorities. The current implementation of the agr
driver always performs active-mode LACP and uses 0x8000 as system and port priorities.
The agr driver uses the MAC address of the first-added physical interface as the MAC address of the agr interface itself. Thus, removing the
physical interface and using it for another purpose can result in non-unique MAC addresses.
The current implementation of the agr driver doesn't prevent unsafe operations like some ioctls against underlying physical interfaces. Such
operations can result in unexpected behaviors, and are strongly discouraged.
There is no way to configure agr interfaces without attaching physical interfaces.
Physical interfaces being added to the agr interface shouldn't have any addresses except for link level address. Otherwise, the attempt will
fail with EBUSY. Note that it includes an automatically assigned IPv6 link-local address.
BSD February 23, 2010 BSD