You do not define IP address of tagged VLAN on aggr0.
In your case you should :
Delete the address
Define the above address on VLAN interface vlan2170
Try pinging the gateway then.
Only native VLAN (untagged) will work on aggr0, while others such as 2170 will work on vlan2170 interface.
Those vlanNUM interfaces are the ones you configure IP address on for tagged VLAN(s) you created with dladm create-vlan ... over aggr0
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
LEARN ABOUT DEBIAN
flow-print
flow-print(1) General Commands Manual flow-print(1)NAME
flow-print -- Display flows in formatted ASCII.
SYNOPSIS
flow-print [-hlnpw] [-d debug_level] [-f format]
DESCRIPTION
The flow-print utility will display flow data in ASCII using pre-defined formats selectable with -f.
Some of the less descriptive column headers are defined below
Header Description
-------------------------------
Sif Source Interface ifIndex.
DiF Destination Interface ifIndex.
Pr Protocol.
P Protocol.
SrcP Source Port.
DstP Destination Port.
Pkts Packets.
Octets Octets (Bytes).
Active Time in ms the flow was active.
B/Pk Bytes per Packet.
Ts Type of Service.
Fl Flags, for TCP the cumulative or of the TCP control bits.
srcAS Source AS.
dstAS Destination AS.
Start Start time of the flow.
End End time of the flow.
router_sc V7 IP address of router producing shorcuts.
peer_nexthop V6 IP address of peer next hop IP address.
encap i/o Version 6 only. Encapsulation size in/out
duration Time in ms the flow was active.
input Input Interface ifIndex.
output Output Interface ifIndex.
flows Number of aggregated flows.
mTos V8.x ToS of pkts that exceeded the contract.
xpackets V8.x Packets that exceed the contract.
OPTIONS -d debug_level
Enable debugging.
-f format Select format. The default is appropriate for the export type of the flow data. Available formats are:
0 1 line, interfaces, hex ports
1 2 line (includes timing and flags)
2 2 line candidate TCP syn attack flows
3 1 line, no interfaces, decimal ports
4 1 line with AS number
5 1 line, 132 column
6 show ip accounting emulation
7 1 line, 132 column +router_id
8 1 line, 132 column +encapsulation
9 1 line with tag values
10 AS aggregation
11 Protocol Port aggregation
12 Source Prefix aggregation
13 Destination Prefix aggregation
14 Prefix aggregation
15 Destination aggregation (Catalyst)
16 Source Destination aggregation (Catalyst)
17 Full Flow (Catalyst)
18 ToS AS Aggregation
19 ToS Proto Port aggregation
20 ToS Source Prefix aggregation
21 ToS Destination Prefix aggregation
22 ToS Prefix Aggregation
23 ToS Prefix Port aggregation
24 Full (Catalyst)
-h Display help.
-l Unbuffer output.
-n Use symbolic names where appropriate.
-p Display header information.
-w Wide output.
EXAMPLES
Display flows in flowfile
flow-print < flowfile
FILES
Configuration files:
Symbols - /etc/flow-tools/sym/*.
BUGS
None known.
AUTHOR
Mark Fullmer maf@splintered.net
SEE ALSO flow-tools(1)flow-print(1)