03-02-2020
if the HBA are connected to SAn switches, I will to verify in errors appear in the ports, exits several types or errors, each type of errors could be help to identify the root cause, inclusive exist piort configuration that could be wrong.
What brand of FC switche are?
10 More Discussions You Might Find Interesting
1. Solaris
Has anyone configured one of these things, I cant seem to find any documentation on sunsolve, I want to verify that it is up and running... (1 Reply)
Discussion started by: csaunders
1 Replies
2. Solaris
Hi all,
I have a compatibly issues with a new hardware
My config is the following one :
Solaris 10
V490 Hardware
2 X HBA Qlogic 2310f cards
An HP EVA 5000 for storage ...
Veritas VxVM 4.1 MP1
When I reboot my server, VxVM is trying to mount/use the volume before it's... (0 Replies)
Discussion started by: unclefab
0 Replies
3. HP-UX
I need information what maximum error level on FC card need clasification of critical level (SAN mass storidge)
Please write screenshot from utility fcutil whith test option.
Pawel (0 Replies)
Discussion started by: pawel_ul
0 Replies
4. UNIX for Advanced & Expert Users
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (3 Replies)
Discussion started by: ronbarak
3 Replies
5. Solaris
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (4 Replies)
Discussion started by: ronbarak
4 Replies
6. Solaris
I installed a FC array for the first time and everything looks OK
in mpathadm, cfgadm, but I don't know what to do next.
# stmsboot -L
non-STMS device name STMS device name
------------------------------------------------------------------
/dev/rdsk/c2t1d0 ... (3 Replies)
Discussion started by: photon
3 Replies
7. Solaris
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies
8. Solaris
Hello all,
how can i see configured fc tapes in solaris system and how can i install a new fc shared tape device , thanks
Best Regards (2 Replies)
Discussion started by: bogacd
2 Replies
9. IP Networking
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies
10. Solaris
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
LEARN ABOUT FREEBSD
brand.4th
BRAND.4TH(8) BSD System Manager's Manual BRAND.4TH(8)
NAME
brand.4th -- FreeBSD ASCII art boot module
DESCRIPTION
The file that goes by the name of brand.4th is a set of commands designed to draw the ASCII art BSD brand above the boot loader menu. The
commands of brand.4th by themselves are not enough for most uses. Please refer to the examples below for the most common situations, and to
loader(8) for additional commands.
Before using any of the commands provided in brand.4th, it must be included through the command:
include brand.4th
This line is present in the default /boot/menu.rc file, so it is not needed (and should not be re-issued) in a normal setup.
The commands provided by it are:
draw-brand Draws the BSD brand.
The brand that is drawn is configured by setting the loader_brand variable in loader.conf(5) to one of ``fbsd''
(the default) or ``none''.
The position of the logo can be configured by setting the loader_brand_x and loader_brand_y variables in
loader.conf(5). The default values are 2 (x) and 1 (y).
The environment variables that effect its behavior are:
loader_brand
Selects the desired brand in the beastie boot menu. Possible values are: ``fbsd'' (default) or ``none''.
loader_brand_x
Sets the desired column position of the brand. Default is 2.
loader_brand_y
Sets the desired row position of the brand. Default is 1.
FILES
/boot/loader The loader(8).
/boot/brand.4th brand.4th itself.
/boot/loader.rc loader(8) bootstrapping script.
EXAMPLES
Set FreeBSD brand in loader.conf(5):
loader_brand="fbsd"
SEE ALSO
loader.conf(5), loader(8)
HISTORY
The brand.4th set of commands first appeared in FreeBSD 9.0.
AUTHORS
The brand.4th set of commands was written by Devin Teske <dteske@FreeBSD.org>.
BSD
May 18, 2011 BSD