02-28-2020
Thanks for confirming the behavior of TFTP for AIX.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
ok, I configured inetd.conf so that the tftp string
is not commented out, but I cannot get the process to start.
I'm running Solaris 5.8 and need some help.
Cabletron said that it's process is 3485, i tried to kill it, it's the wrong process. I started inetd again and still can't kill it.
i... (15 Replies)
Discussion started by: veitcha
15 Replies
2. UNIX for Dummies Questions & Answers
Is it possible to copy files between two computers with TFTP.And how? (1 Reply)
Discussion started by: bericica
1 Replies
3. UNIX for Advanced & Expert Users
Hello,
we practise our server with operating system ReliantUNIX 5.45 and we are using Informix Dynamic Server 7.31.
I ascertained a lot of cpu interrupts per second (int/s). The count of int/s exceeds critical maximum value considerably.
Machine specific notes for Informix Dynamic Server... (1 Reply)
Discussion started by: urbale
1 Replies
4. UNIX for Advanced & Expert Users
Double question here ... Running on Debian Etch and Apache 2.0
1) Using mod_proxy and/or mod_proxy_http in apache 2.0.
The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies
5. Solaris
Hello Dear Everyone.
Have you Gurus perhaps got an idea how to bind a particular application/program to specific IP address on solaris box?
Assume there is a server with two NICs with distinct IPs, I install an application (could be a backup sowftware client) and would like to tell to the... (6 Replies)
Discussion started by: togr
6 Replies
6. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
7. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
8. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
TFTP(1) General Commands Manual TFTP(1)
NAME
tftp - trivial file transfer program
SYNOPSIS
tftp [ host ]
DESCRIPTION
Tftp is the user interface to the Internet TFTP (Trivial File Transfer Protocol), which allows users to transfer files to and from a remote
machine. The remote host may be specified on the command line, in which case tftp uses host as the default host for future transfers (see
the connect command below).
COMMANDS
Once tftp is running, it issues the prompt tftp> and recognizes the following commands:
connect host-name [ port ]
Set the host (and optionally port) for transfers. Note that the TFTP protocol, unlike the FTP protocol, does not maintain connec-
tions betweeen transfers; thus, the connect command does not actually create a connection, but merely remembers what host is to be
used for transfers. You do not have to use the connect command; the remote host can be specified as part of the get or put com-
mands.
mode transfer-mode
Set the mode for transfers; transfer-mode may be one of ascii or binary. The default is ascii.
put file
put localfile remotefile
put file1 file2 ... fileN remote-directory
Put a file or set of files to the specified remote file or directory. The destination can be in one of two forms: a filename on the
remote host, if the host has already been specified, or a string of the form host:filename to specify both a host and filename at
the same time. If the latter form is used, the hostname specified becomes the default for future transfers. If the remote-direc-
tory form is used, the remote host is assumed to be a UNIX machine.
get filename
get remotename localname
get file1 file2 ... fileN
Get a file or set of files from the specified sources. Source can be in one of two forms: a filename on the remote host, if the
host has already been specified, or a string of the form host:filename to specify both a host and filename at the same time. If the
latter form is used, the last hostname specified becomes the default for future transfers.
quit Exit tftp. An end of file also exits.
verbose
Toggle verbose mode.
trace Toggle packet tracing.
status Show current status.
rexmt retransmission-timeout
Set the per-packet retransmission timeout, in seconds.
timeout total-transmission-timeout
Set the total transmission timeout, in seconds.
ascii Shorthand for "mode ascii"
binary Shorthand for "mode binary"
? [ command-name ... ]
Print help information.
BUGS
Because there is no user-login or validation within the TFTP protocol, the remote site will probably have some sort of file-access restric-
tions in place. The exact methods are specific to each site and therefore difficult to document here.
4.3 Berkeley Distribution 1Q TFTP(1)