02-28-2020
Thanks for confirming the behavior of TFTP for AIX.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
ok, I configured inetd.conf so that the tftp string
is not commented out, but I cannot get the process to start.
I'm running Solaris 5.8 and need some help.
Cabletron said that it's process is 3485, i tried to kill it, it's the wrong process. I started inetd again and still can't kill it.
i... (15 Replies)
Discussion started by: veitcha
15 Replies
2. UNIX for Dummies Questions & Answers
Is it possible to copy files between two computers with TFTP.And how? (1 Reply)
Discussion started by: bericica
1 Replies
3. UNIX for Advanced & Expert Users
Hello,
we practise our server with operating system ReliantUNIX 5.45 and we are using Informix Dynamic Server 7.31.
I ascertained a lot of cpu interrupts per second (int/s). The count of int/s exceeds critical maximum value considerably.
Machine specific notes for Informix Dynamic Server... (1 Reply)
Discussion started by: urbale
1 Replies
4. UNIX for Advanced & Expert Users
Double question here ... Running on Debian Etch and Apache 2.0
1) Using mod_proxy and/or mod_proxy_http in apache 2.0.
The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies
5. Solaris
Hello Dear Everyone.
Have you Gurus perhaps got an idea how to bind a particular application/program to specific IP address on solaris box?
Assume there is a server with two NICs with distinct IPs, I install an application (could be a backup sowftware client) and would like to tell to the... (6 Replies)
Discussion started by: togr
6 Replies
6. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
7. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
8. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT FREEBSD
tftp-proxy
TFTP-PROXY(8) BSD System Manager's Manual TFTP-PROXY(8)
NAME
tftp-proxy -- Internet Trivial File Transfer Protocol proxy
SYNOPSIS
tftp-proxy [-v] [-w transwait]
DESCRIPTION
tftp-proxy is a proxy for the Internet Trivial File Transfer Protocol invoked by the inetd(8) internet server. TFTP connections should be
redirected to the proxy using the pf(4) rdr command, after which the proxy connects to the server on behalf of the client.
The proxy establishes a pf(4) rdr rule using the anchor facility to rewrite packets between the client and the server. Once the rule is
established, tftp-proxy forwards the initial request from the client to the server to begin the transfer. After transwait seconds, the pf(4)
NAT state is assumed to have been established and the rdr rule is deleted and the program exits. Once the transfer between the client and
the server is completed, the NAT state will naturally expire.
Assuming the TFTP command request is from $client to $server, the proxy connected to the server using the $proxy source address, and $port is
negotiated, tftp-proxy adds the following rule to the anchor:
rdr proto udp from $server to $proxy port $port -> $client
The options are as follows:
-v Log the connection and request information to syslogd(8).
-w transwait
Number of seconds to wait for the data transmission to begin before removing the pf(4) rdr rule. The default is 2 seconds.
CONFIGURATION
To make use of the proxy, pf.conf(5) needs the following rules. The anchors are mandatory. Adjust the rules as needed for your configura-
tion.
In the NAT section:
nat on $ext_if from $int_if -> ($ext_if:0)
no nat on $ext_if to port tftp
rdr-anchor "tftp-proxy/*"
rdr on $int_if proto udp from $lan to any port tftp ->
127.0.0.1 port 6969
In the filter section, an anchor must be added to hold the pass rules:
anchor "tftp-proxy/*"
inetd(8) must be configured to spawn the proxy on the port that packets are being forwarded to by pf(4). An example inetd.conf(5) entry fol-
lows:
127.0.0.1:6969 dgram udp wait root
/usr/libexec/tftp-proxy tftp-proxy
SEE ALSO
tftp(1), pf(4), pf.conf(5), ftp-proxy(8), inetd(8), syslogd(8), tftpd(8)
CAVEATS
tftp-proxy chroots to /var/empty and changes to user ``proxy'' to drop privileges.
BSD
November 28, 2005 BSD