ok, I configured inetd.conf so that the tftp string
is not commented out, but I cannot get the process to start.
I'm running Solaris 5.8 and need some help.
Cabletron said that it's process is 3485, i tried to kill it, it's the wrong process. I started inetd again and still can't kill it.
i... (15 Replies)
Hello,
we practise our server with operating system ReliantUNIX 5.45 and we are using Informix Dynamic Server 7.31.
I ascertained a lot of cpu interrupts per second (int/s). The count of int/s exceeds critical maximum value considerably.
Machine specific notes for Informix Dynamic Server... (1 Reply)
Double question here ... Running on Debian Etch and Apache 2.0
1) Using mod_proxy and/or mod_proxy_http in apache 2.0.
The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Hello Dear Everyone.
Have you Gurus perhaps got an idea how to bind a particular application/program to specific IP address on solaris box?
Assume there is a server with two NICs with distinct IPs, I install an application (could be a backup sowftware client) and would like to tell to the... (6 Replies)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT REDHAT
tftp
TFTP(1) UNIX User's Manual TFTP(1)NAME
tftp - IPv4 Trivial File Transfer Protocol client
SYNOPSIS
tftp [options...] [host]
DESCRIPTION
tftp is a client for the IPv4 Trivial file Transfer Protocol, which can be used to transfer files to and from remote machines, including
some very minimalistic, usually embedded, systems. The remote host may be specified on the command line, in which case tftp uses host as
the default host for future transfers (see the connect command below.)
OPTIONS -v Default to verbose mode.
-V Print the version number and configuration to standard output, then exit gracefully.
COMMANDS
Once tftp is running, it issues the prompt tftp> and recognizes the following commands:
? command-name...
help command-name...
Print help information
ascii Shorthand for mode ascii.
binary Shorthand for mode binary.
connect host [port]
Set the host (and optionally port) for transfers. Note that the TFTP protocol, unlike the FTP protocol, does not maintain connec-
tions between transfers; thus, the connect command does not actually create a connection, but merely remembers what host is to be
used for transfers. You do not have to use the connect command; the remote host can be specified as part of the get or put com-
mands.
get file
get remotefile localfile
get file1 file2 file3...
Get a file or set of files from the specified sources. A remote filename can be in one of two forms: a plain filename on the remote
host, if the host has already been specified, or a string of the form host:filename to specify both a host and filename at the same
time. If the latter form is used, the last hostname specified becomes the default for future transfers.
mode transfer-mode
Specify the mode for transfers; transfer-mode may be one of ascii (or netascii) or binary (or octet.) The default is ascii.
put file
put localfile remotefile
put file1 file2 file3... remote-directory
Put a file or set of files to the specified remote file or directory. The destination can be in one of two forms: a filename on the
remote host, if the host has already been specified, or a string of the form host:filename to specify both a host and filename at
the same time. If the latter form is used, the hostname specified becomes the default for future transfers. If the remote-direc-
tory form is used, the remote host is assumed to be a UNIX system or another system using / as directory separator.
quit Exit tftp. End-of-file will also exit.
rexmt retransmission-timeout
Set the per-packet retransmission timeout, in seconds.
status Show current status.
timeout total-transmission-timeout
Set the total transmission timeout, in seconds.
trace Toggle packet tracing (a debugging feature.)
verbose
Toggle verbose mode.
NOTES
The TFTP protocol provides no provisions for authentication or security. Therefore, the remote server will probably implement some kinds
of access restriction or firewalling. These access restrictions are likely to be site- and server-specific.
AUTHOR
This version of tftp is maintained by H. Peter Anvin <hpa@zytor.com>. It was derived from, but has substantially diverged from, an OpenBSD
source base, with added patches by Markus Gutschke and Gero Kulhman.
SEE ALSO tftpd(8).
tftp-hpa 0.32 13 November 2001 TFTP(1)