Extremely low throughput between AIX 7.2 and RHEL Maipo Post: 303044525

9 More Discussions You Might Find Interesting

1. IP Networking

Gigabit Link throughput

As a rule of thumb in doing calculations, what figure would you use in Mbytes/sec? I know the answer varies grealty on the topolgy of the network but I wonde what newteok engineers use a rough rule of thumb? Many thanks.

2. IP Networking

How to improve throughput?

I have a 10Gbps network link connecting two machines A and B. I want to transfer 20GB data from A to B using TCP. With default setting, I can use 50% bandwidth. How to improve the throughput? Is there any way to make throughput as close to 10Gbps as possible? thanks~ :)

3. UNIX for Dummies Questions & Answers

SOLARIS vs AIX vs RHEL

Hi I'm wondering what are the differences between SOLARIS, AIX and RHEL ? I would like to know in which operating system is best for what kind of implementation ? Why some companies use Solaris instead of e.g. AIX and etc. ? thx for help.

4. AIX

Migrating RHEL 5 UNIX users to AIX

Hi, I'm able to migrate UNIX users/groups from Solaris to AIX (with same password using 13-char encrypted password from shadow file) but no luck with RHEL 5 to AIX. I see encrypted password in RHEL 5 is bit lengthier than 13-char. Is there any way to convert encrypted password such that same...

5. AIX

High Runqueue (R) LOW CPU LOW I/O Low Network Low memory usage

Hello All I have a system running AIX 61 shared uncapped partition (with 11 physical processors, 24 Virtual 72GB of Memory) . The output from NMON, vmstat show a high run queue (60+) for continous periods of time intervals, but NO paging, relatively low I/o (6000) , CPU % is 40, Low network....

6. Red Hat

High RAM usage, extremely low swapping

Hi team I have three physical servers running on Red Hat Enterprise Linux Server release 6.2 with the following memory conditions: # cat /proc/meminfo | grep -i mem MemTotal: 8062888 kB MemFree: 184540 kB Shmem: 516 kB and the following swap conditions: ...

7. UNIX for Advanced & Expert Users

Help understanding differences between AIX and RHEL

I have started a new job which requires AIX admin skills, which I have, and RHEL skills. Does anyone have a cheat sheet that if I know how to solve the problem in AIX how would I do that in RHEL? I was an IBM pre-sales technical trying to keep sales guys honest - not possible. Any other links to...

8. Shell Programming and Scripting

AIX to RHEL migration - awk treating 0e[0-9]+ as 0 instead of string issue

Greetings Experts, We are migrating from AIX to RHEL Linux. I have created a script to verify and report the NULLs and SPACEs in the key columns and duplicates on key combination of "|" delimited set of big files. Following is the code that was successfully running in AIX. awk -F "|" 'BEGIN {...

9. AIX

Question about shared filesystem btw AIX and RHEL

We found out that the Spectrum Scale (GPFS) doesnt support mix nodes (AIX and RHEL) on direct attached storage. Is there any other options besides NFS for mix O/S? Trying to avoid network type of shared filesystem which might end up high traffic on IO because we do run backup jobs on those...

LEARN ABOUT DEBIAN

gnunet-vpn

GNUNET-VPN(1)						      General Commands Manual						     GNUNET-VPN(1)

NAME

       gnunet-vpn - manually setup a GNUnet VPN tunnel

SYNOPSIS

       gnunet-vpn [options]

DESCRIPTION

       gnunet-vpn  can	be  used  to manually setup a VPN tunnel via the GNUnet network.  There are two main types of tunnels.	Tunnels to an exit
       node which routes the traffic to the global Internet, and tunnels to a node that runs a service only within GNUnet.  Depending on the  type
       of  tunnel, gnunet-vpn takes different options.	The "-i" option is required for tunnels to an exit node, whereas the "-p" and "-s" options
       in conjunction with either "-u" or "-t" are required for tunnels to services.  For exit tunnels, both UDP and TCP  traffic  will  be  redi-
       rected.	For service tunnels, either UDP ("-u") or TCP ("-t") traffic will be redirected.

       The  tool  will	display the IP address for this end of the tunnel.  The address can be displayed as soon as it has been allocated, or only
       after ("-a") the tunnel has been created.

OPTIONS

       -4, --ipv4
	      Desired IP address on this end of the tunnel should be an IPv4 address.

       -6, --ipv6
	      Desired IP address on this end of the tunnel should be an IPv6 address.

       -a, --after-connect
	      Display IP address only after the tunnel is fully connected.

       -c FILENAME,  --config=FILENAME
	      Use the configuration file FILENAME.

       -d SEC, --duration SEC
	      The mapping should be established for SEC seconds.  Default is 5 minutes.

       -h, --help
	      Print short help on options.

       -i IP, --ip IP
	      Tunnel should be to an exit node and connect to the given IPv4 or IPv6 IP address.  Note that you can specify an IPv6 address as the
	      target here, even in combination with "-4" (4to6) and similarly you can specify an IPv4 address in combination with "-6" (6to4).

       -L LOGLEVEL, --loglevel=LOGLEVEL
	      Use LOGLEVEL for logging.  Valid values are DEBUG, INFO, WARNING and ERROR.

       -p PEERID,  --peer=PEERID
	      Name of the peer offering the service to connect to.  Cannot be used in conjunction with "-i", requires "-s".

       -s NAME,  --service=NAME
	      Name of the service running on the target peer.  Cannot be used in conjunction with "-i", requires "-p".

       -t, --tcp
	      Service runs TCP.  Either "-t" or "-u" must be specified when using "-s".

       -u, --udp
	      Service runs UDP.  Either "-t" or "-u" must be specified when using "-s".

       -V, --verbose
	      Be verbose.

       -v, --version
	      Print GNUnet version number.

BUGS

       Report bugs by using Mantis <https://gnunet.org/bugs/> or by sending electronic mail to <gnunet-developers@gnu.org>

SEE ALSO

       gnunet-setup(1)

GNUnet								    25 Feb 2012 						     GNUNET-VPN(1)