Unable to connect to a server from our AIX server via FTP Post: 303044432

Sponsored Content

Top Forums UNIX for Beginners Questions & Answers Unable to connect to a server from our AIX server via FTP Post 303044432 by Bruno2020 on Friday 21st of February 2020 06:08:49 AM

02-21-2020

Registered User

Code:

Linc-HO>ping 164.52.194.12

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 164.52.194.12, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Linc-HO>

Code:

Linc-HO>show ip interface
GigabitEthernet0/0 is up, line protocol is up
  Internet address is 192.168.198.2/30
  Broadcast address is 255.255.255.255
  Address determined by non-volatile memory
  MTU is 1500 bytes
  Helper address is not set
  Directed broadcast forwarding is disabled
  Outgoing access list is not set
  Inbound  access list is not set
  Proxy ARP is enabled
  Local Proxy ARP is disabled
  Security level is default
  Split horizon is enabled
  ICMP redirects are always sent
  ICMP unreachables are always sent
  ICMP mask replies are never sent
  IP fast switching is enabled
  IP fast switching on the same interface is disabled
  IP Flow switching is disabled
  IP CEF switching is enabled
  IP CEF switching turbo vector
  IP multicast fast switching is enabled
  IP multicast distributed fast switching is disabled
  IP route-cache flags are Fast, CEF
  Router Discovery is disabled
  IP output packet accounting is disabled
  IP access violation accounting is disabled
  TCP/IP header compression is disabled
  RTP/IP header compression is disabled
  Policy routing is disabled
  Network address translation is disabled
  BGP Policy Mapping is disabled
  Input features: MCI Check
  WCCP Redirect outbound is disabled
  WCCP Redirect inbound is disabled
  WCCP Redirect exclude is disabled
GigabitEthernet0/1 is up, line protocol is up
  Internet address is 172.16.80.100/16
  Broadcast address is 255.255.255.255
  Address determined by non-volatile memory
  MTU is 1500 bytes
  Helper address is not set
  Directed broadcast forwarding is disabled
  Outgoing access list is not set
  Inbound  access list is not set
  Proxy ARP is enabled
  Local Proxy ARP is disabled
  Security level is default
  Split horizon is enabled
  ICMP redirects are always sent
  ICMP unreachables are always sent
  ICMP mask replies are never sent
  IP fast switching is enabled
  IP fast switching on the same interface is disabled
  IP Flow switching is disabled
  IP CEF switching is enabled
  IP CEF switching turbo vector
  IP multicast fast switching is enabled
  IP multicast distributed fast switching is disabled
  IP route-cache flags are Fast, CEF
  Router Discovery is disabled
  IP output packet accounting is disabled
  IP access violation accounting is disabled
  TCP/IP header compression is disabled
  RTP/IP header compression is disabled
  Policy routing is disabled
  Network address translation is disabled
  BGP Policy Mapping is disabled
  Input features: MCI Check
  WCCP Redirect outbound is disabled
  WCCP Redirect inbound is disabled
  WCCP Redirect exclude is disabled
GigabitEthernet0/2 is down, line protocol is down
  Internet address is 10.224.102.13/30
  Broadcast address is 255.255.255.255
  Address determined by non-volatile memory
  MTU is 1500 bytes
  Helper address is not set
  Directed broadcast forwarding is disabled
  Outgoing access list is not set
  Inbound  access list is not set
  Proxy ARP is enabled
  Local Proxy ARP is disabled
  Security level is default
  Split horizon is enabled
  ICMP redirects are always sent
  ICMP unreachables are always sent
  ICMP mask replies are never sent
  IP fast switching is enabled
  IP fast switching on the same interface is disabled
  IP Flow switching is disabled
  IP CEF switching is enabled
  IP CEF switching turbo vector
  IP multicast fast switching is enabled
  IP multicast distributed fast switching is disabled
  IP route-cache flags are Fast, CEF
  Router Discovery is disabled
  IP output packet accounting is disabled
  IP access violation accounting is disabled
  TCP/IP header compression is disabled
  RTP/IP header compression is disabled
  Policy routing is disabled
  Network address translation is disabled
  BGP Policy Mapping is disabled
  Input features: MCI Check
  WCCP Redirect outbound is disabled
  WCCP Redirect inbound is disabled
  WCCP Redirect exclude is disabled
Serial0/0/0 is down, line protocol is down
  Internet address is 10.10.10.6/30
  Broadcast address is 255.255.255.255
  Address determined by non-volatile memory
  MTU is 1500 bytes
  Helper address is not set
  Directed broadcast forwarding is disabled
  Outgoing access list is not set
  Inbound  access list is not set
  Proxy ARP is enabled
  Local Proxy ARP is disabled
  Security level is default
  Split horizon is enabled
  ICMP redirects are always sent
  ICMP unreachables are always sent
  ICMP mask replies are never sent
  IP fast switching is enabled
  IP fast switching on the same interface is enabled
  IP Flow switching is disabled
  IP CEF switching is enabled
  IP CEF switching turbo vector
  IP multicast fast switching is enabled
  IP multicast distributed fast switching is disabled
  IP route-cache flags are Fast, CEF
  Router Discovery is disabled
  IP output packet accounting is disabled
  IP access violation accounting is disabled
  TCP/IP header compression is disabled
  RTP/IP header compression is disabled
  Policy routing is disabled
  Network address translation is disabled
  BGP Policy Mapping is disabled
  Input features: MCI Check
  WCCP Redirect outbound is disabled
  WCCP Redirect inbound is disabled
  WCCP Redirect exclude is disabled
Serial0/0/1 is down, line protocol is down
  Internet address is 10.10.10.9/30
  Broadcast address is 255.255.255.255
  Address determined by non-volatile memory
  MTU is 1500 bytes
  Helper address is not set
  Directed broadcast forwarding is disabled
  Outgoing access list is not set
  Inbound  access list is not set
  Proxy ARP is enabled
  Local Proxy ARP is disabled
  Security level is default
  Split horizon is enabled
  ICMP redirects are always sent
  ICMP unreachables are always sent
  ICMP mask replies are never sent
  IP fast switching is enabled
  IP fast switching on the same interface is enabled
  IP Flow switching is disabled
  IP CEF switching is enabled
  IP CEF switching turbo vector
  IP multicast fast switching is enabled
  IP multicast distributed fast switching is disabled
  IP route-cache flags are Fast, CEF
  Router Discovery is disabled
  IP output packet accounting is disabled
  IP access violation accounting is disabled
  TCP/IP header compression is disabled
  RTP/IP header compression is disabled
  Policy routing is disabled
  Network address translation is disabled
  BGP Policy Mapping is disabled
  Input features: MCI Check
  WCCP Redirect outbound is disabled
  WCCP Redirect inbound is disabled
  WCCP Redirect exclude is disabled
Serial0/1/0 is down, line protocol is down
  Internet address is 10.10.10.13/30
  Broadcast address is 255.255.255.255
  Address determined by non-volatile memory
  MTU is 1500 bytes
  Helper address is not set
  Directed broadcast forwarding is disabled
  Outgoing access list is not set
  Inbound  access list is not set
  Proxy ARP is enabled
  Local Proxy ARP is disabled
  Security level is default
  Split horizon is enabled
  ICMP redirects are always sent
  ICMP unreachables are always sent
  ICMP mask replies are never sent
  IP fast switching is enabled
  IP fast switching on the same interface is enabled
  IP Flow switching is disabled
  IP CEF switching is enabled
  IP CEF switching turbo vector
  IP multicast fast switching is enabled
  IP multicast distributed fast switching is disabled
  IP route-cache flags are Fast, CEF
  Router Discovery is disabled
  IP output packet accounting is disabled
  IP access violation accounting is disabled
  TCP/IP header compression is disabled
  RTP/IP header compression is disabled
  Policy routing is disabled
  Network address translation is disabled
  BGP Policy Mapping is disabled
  Input features: MCI Check
  WCCP Redirect outbound is disabled
  WCCP Redirect inbound is disabled
  WCCP Redirect exclude is disabled
Serial0/1/1 is up, line protocol is up
  Internet address is 10.10.10.21/30
  Broadcast address is 255.255.255.255
  Address determined by non-volatile memory
  Peer address is 10.10.10.22
  MTU is 1500 bytes
  Helper address is not set
  Directed broadcast forwarding is disabled
  Outgoing access list is not set
  Inbound  access list is not set
  Proxy ARP is enabled
  Local Proxy ARP is disabled
  Security level is default
  Split horizon is enabled
  ICMP redirects are always sent
  ICMP unreachables are always sent
  ICMP mask replies are never sent
  IP fast switching is enabled
  IP fast switching on the same interface is enabled
  IP Flow switching is disabled
  IP CEF switching is enabled
  IP CEF switching turbo vector
  IP multicast fast switching is enabled
  IP multicast distributed fast switching is disabled
  IP route-cache flags are Fast, CEF
  Router Discovery is disabled
  IP output packet accounting is disabled
  IP access violation accounting is disabled
  TCP/IP header compression is disabled
  RTP/IP header compression is disabled
  Policy routing is disabled
  Network address translation is disabled
  BGP Policy Mapping is disabled
  Input features: MCI Check
  WCCP Redirect outbound is disabled
  WCCP Redirect inbound is disabled
  WCCP Redirect exclude is disabled

Bruno2020

View Public Profile for Bruno2020

Find all posts by Bruno2020

10 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

ftp script not able to connect to ftp server.

I have the following ftp script to get files from a remote location. However, on running the script I find that I am not even able to connect to ftp server. I am able to connect to ftp server using other GUI ftp tools like WS_FTP using the same IP. IP used here is a dummy IP. What can go...

2. AIX

Unable to connect to AIX server through xmanager

Hi, I have xmanager installed on my windows PC. But I am not able to connect to AIX server. It's giving the error as follows: The X11 forwarding request was rejected. Graphics mode is not coming up in AIX server. Please help as I have to install oracle patchset urgently.

3. HP-UX

[Solved] Unable to rename file in ftp server .Net:FTP perl

Hello All, I am trying to connect to ftp server and get the files. Also i need to rename the file in other ftp dir. rename method is not allowing me to rename the file in other dir. When i tried copy command by using net::FTP:FILE then perl says it is not installed. Can some body help me to...

4. UNIX for Advanced & Expert Users

Unable to use FTP command to connect from one server to another

Hi, I have two unix servers A and B. from A i am trying to use the ftp command to connect to B but I am getting the "ftp: connect: A remote host refused an attempted connect operation." I checked the following things : 1.) Unix Server details for A and B after running the command uname -a...

5. Red Hat

unable to connect remote server using ssh

hi all i am unable to connect remote server using ssh but i am able to ping the server ssh service is running.

6. Linux

Generate public key to connect from one ftp server to other server

How to generate public key to connect from one ftp server to other server to use in scripting.

7. UNIX for Advanced & Expert Users

Public key to connect from one ftp server to other server

How to generate public key to connect from one ftp server to other server to use in scripting.

8. Linux

Unable to connect to Server machine from a client machine using ftp service

Hi, Could you please help me with the below issue.. I'm running RHEL6 OS on both server (192.168.0.10) and client machines (192.168.0.1). I'm trying to connect to server from the client machine using ftp service. I have installed vsftpd daemon on both the machines. I'm getting...

9. Solaris

Unable to connect sun server.

Hi, I am unable to connect sun server, server model is sun fire v440 on server 2 ports are there. serial management, and network management. I would like to know how to connect serial port if I dont have com port on my system? and on Network Management no ip address is configured. ...

10. Shell Programming and Scripting

Not able to connect to new FTP server

Hi All, We have done new FTB setup. I am not able to to connect to this new target server. Here is the new setup to send files to the FTB : - Login : FTB-TAN-DEV-SAP - Protocol : SFTP - Port : 54322 - Hostname : ftb-dev.apj.hp - Env : DEV - Target ID : 3225 I tried connecting to the...