iptables -A INPUT -s 117.144.138.130/24 -j DROP # rogue chinese bot
iptables -A INPUT -s 116.232.49.231/24 -j DROP # rogue chinese bot
Empty the "trap" again and block two Chinese subnetworks with rouge, unidentified bot activity.
Honestly, this is starting to "annoy me a lot" in the possibility that these performance hits, and all the time I am spending to find the cause of these hits / spikes, wasting valuable "time in life" is related to rouge, unidentified bots from Chinese networks.
If this continues, I am going to start blocking Chinese networks at the /16 and /8 levels (entire networks).
First, let's see if this is indeed the main source of these spikes. As we all know from situational awareness theory and the famous OODA loop by John Boyd.
OBSERVE
ORIENT
DECIDE
ACT
Already, we have enough information to ACT. But lets continue to OBSERVE
The loop goes on ... and on ....
Please note that we cannot trust apache2 modules and other third-party software to automatically block IPs, because this can results in blocking the "good bots" which are important for search engine optimization and site traffic.
That means, if this is confirmed that these kinds of bots continue to be the cause of problems, then I will need to DECIDE how to deal with this situation moving forward. I think point in time, I am going to continue to "trap and trace" before making a decision. However, it does seem, at this point, that rouge, unidentified bots from Chinese networks are causing performance issues and need to be "dealt with".
If anyone else has experienced similar issues and has an interesting potential solution to this problem, please reply and share your ideas.
Thanks!
PS: I may consider automating this, as follows:
Capture network session activity when one minute load average exceeds a threshold (as I am doing now).
Filter results captured in the DB based on "hitcount" and "country".
If the "hitcount" exceeds a certain threshold and "country" is in an array of "known to have rouge bots countries".
we have an unix system which has
load average normally about 20.
but while i am running a particular unix batch which performs heavy
operations on filesystem and database average load
reduces to 15.
how can we explain this situation?
while running that batch idle cpu time is about %60-65... (0 Replies)
Hello all, I have a question about load averages.
I've read the man pages for the uptime and w command for two or three different flavors of Unix (Red Hat, Tru64, Solaris). All of them agree that in the output of the 2 aforementioned commands, you are given the load average for the box, but... (3 Replies)
Hello, Here is the output of top command. My understanding here is,
the load average 0.03 in last 1 min, 0.02 is in last 5 min, 0.00 is in last 15 min.
By seeing this load average, When can we say that, the system load averge is too high?
When can we say that, load average is medium/low??... (8 Replies)
Hi,
i have installed solaris 10 on t-5120 sparc enterprise.
I am little surprised to see load average of 2 or around on this OS.
when checked with ps command following process is using highest CPU. looks like it is running for long time and does not want to stop, but I do not know... (5 Replies)
Hello AlL,..
I want from experts to help me as my load average is increased and i dont know where is the problem !!
this is my top result :
root@a4s # top
top - 11:30:38 up 40 min, 1 user, load average: 3.06, 2.49, 4.66
Mem: 8168788k total, 2889596k used, 5279192k free, 47792k... (3 Replies)
Hi ,
I am using 48 CPU sunOS server at my work.
The application has facility to check the current load average before starting a new process to control the load.
Right now it is configured as 48. So it does mean that each CPU can take maximum one proces and no processe is waiting.
... (2 Replies)
Hi,
I am getting a high load average, around 7, once an hour. It last for about 4 minutes and makes things fairly unusable for this time.
How do I find out what is using this. Looking at top the only thing running at the time is md5sum.
I have looked at the crontab and there is nothing... (10 Replies)
Here we go....
Preface:
..... so in a galaxy far, far, far away from commercial, data sharing corporations.....
For this project, I used the ESP-WROOM-32 as an MQTT (publish / subscribe) client which receives Linux server "load averages" as messages published as MQTT pub/sub messages.... (6 Replies)
Discussion started by: Neo
6 Replies
LEARN ABOUT DEBIAN
nwfsctrl
NWFSCTRL(8) nwfsctrl NWFSCTRL(8)NAME
nwfsctrl - Perform server command
SYNOPSIS
nwfsctrl [ -h ] [ -S server ] [ -U user name ] [ -P password | -n ] [ -C ] [ -p ncpfs path ] -c | -o | -[f]d
nwfsctrl [ -h ] [ -S server ] [ -U user name ] [ -P password | -n ] [ -C ] [ -p ncpfs path ] server command
DESCRIPTION
nwfsctrl performs command on server.
OPTIONS -h
With -h nwfsctrl prints a little help text.
-S server
is the name of the server you want to use.
-U user
user is the user name to use for login. To set the server's time, you need supervisor privileges.
-P password
password is the password to use for login. If neither -n nor -P are given, and the user has no open connection to the server, nwfstime
prompts for a password.
-n
-n should be given if no password is required for the login. As you need supervisor privileges for setting the date and time, this
option is probably not used very often.
-C
By default, passwords are converted to uppercase before they are sent to the server, because most servers require this. You can turn off
this conversion by -C.
-o
Open bindery.
-c
Close bindery.
-d
Down fileserver. This command will complain if there are open files on server.
-fd
Down fileserver, regardless of opened files.
load module options...
Load module module with options options... on server. Program will complain if module is already loaded.
unload module
Unload module module from server. Program will complain if module is not loaded.
mount volume
Mount volume volume.
dismount volume
Dismount volume volume. If there are open files on volume, server displays prompt on console. You must go to the server (or telnet/xcon-
sole) and hit Y or N to get beyond this point).
set variable = value
Set server settable variable variable to value value.
open bindery
Open bindery.
close bindery
Close bindery.
enable login
Enable login to file server.
disable login
Disable login to file server.
disable tts
Disable TTS. This probably does not work on Netware 4.11.
enable tts
Enable TTS. This probably does not work on Netware 4.11.
BUGS
Other commands are not written yet (volume, clear connection ...)
CREDITS
This utility was created by Petr Vandrovec (vandrove@vc.cvut.cz) and is part of ncpfs since 2.2.0.11.
nwfsctrl 2/12/1999 NWFSCTRL(8)
02-15-2020
