02-03-2020
UPDATE
I fixed the "no write access problem" by grepping for proceses named "telnet" and then killing them. Then I tried the "telnet localhost 5000" again and it worked fine. I next ran "svcs -xv" again and this time the "OCM process in maintenane mode" wasn't listed there anymore. So that seems to have fixed itself. Go figure.
This User Gave Thanks to Michele31416 For This Post:
8 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have issues installing Solaris into a LDom using a Solaris10u5/08 DVD. I have been troubleshooting for the past 2 days and I still cannot get it up.
Here is the logs:
root@eld-app2# ldm add-vdsdev /cdrom/sol_10_508_sparc/s0 cdrom0@primary-vds0
root@eld-app2# ldm add-vdisk cdrom0... (4 Replies)
Discussion started by: bolasutra
4 Replies
2. Solaris
Hi Gurus
I am in a strange situation.
I have a SUN sparc server . The server was having an IP say X..... (this IP X is now being used by another server)..... I have just installed fresh solaris 9 OS on the same server and given new IP say Y.
I also configured probe based IPMP with ce0 and... (2 Replies)
Discussion started by: ningy
2 Replies
3. Solaris
I have viewed a few previous posts regarding this, but none of them quite described or worked with my issue.
I am out of local disk space on my LDOM Manager but still have plenty of SAN vCPU and Memory available so I am trying to install a new LDOM OS on SAN.
I have exposed the SAN to the... (0 Replies)
Discussion started by: MobileGSP
0 Replies
4. Solaris
Apologies if this is the wrong forum..
I have some LDOMs running on a Sparc server. I copied the disk0 file from one chassis over to another, stopped the ldom on the source system and started it on the 2nd one. All fine. Shut it down and flipped back. We then did a fair bit of work on the... (4 Replies)
Discussion started by: tommyq
4 Replies
5. Solaris
Hello,
I am trying to install Solaris 10 on a newly created LDom. Here are the commands I ran to create the LDom:
ldm add-domain ldg2
ldm add-vcpu 8 ldg2
ldm add-memory 2g ldg2
ldm add-vnet vnet2 primary-vsw0 ldg2
ldm add-vdsdev /dev/dsk/c0t5000CCA01535E20Cd0s0 vol2@primary-vds0
ldm... (8 Replies)
Discussion started by: bstring
8 Replies
6. Solaris
Hi,
Our existing environment is having primary domain and 3 guest domains are running over it. See the attached image.
Now we want to add a new primary virtual switch and move LDOM3 to be connected with new primary switch.
So, I am not sure how to achieve this because. If I remove the... (7 Replies)
Discussion started by: praveensharma21
7 Replies
7. Solaris
hello to everyone. im new member here.
i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain.
I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)
Discussion started by: Liam_
2 Replies
8. UNIX for Beginners Questions & Answers
I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest.
This question is basically the... (7 Replies)
Discussion started by: Michele31416
7 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)
NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO
vconfig(8) interfaces(5)
vlan September 30 2007 VLAN-INTERFACES(5)