Your T4 box has 3 IP addresses on three interface, from one which is VNIC net1 net0 vnic0
In one point in time, these addresses have been configured...
If you wish to remove the mentioned address found in this output :
Execute the following on the hypervisor via SP or connected to any other address but 78 via ssh :
The system is complaining for duplicate address since you have one defined on VNIC in hypervisor and same inside LDOM.
Hope that helps
Regards
Peasant.
These 2 Users Gave Thanks to Peasant For This Post:
Hi,
I have issues installing Solaris into a LDom using a Solaris10u5/08 DVD. I have been troubleshooting for the past 2 days and I still cannot get it up.
Here is the logs:
root@eld-app2# ldm add-vdsdev /cdrom/sol_10_508_sparc/s0 cdrom0@primary-vds0
root@eld-app2# ldm add-vdisk cdrom0... (4 Replies)
Hi Gurus
I am in a strange situation.
I have a SUN sparc server . The server was having an IP say X..... (this IP X is now being used by another server)..... I have just installed fresh solaris 9 OS on the same server and given new IP say Y.
I also configured probe based IPMP with ce0 and... (2 Replies)
I have viewed a few previous posts regarding this, but none of them quite described or worked with my issue.
I am out of local disk space on my LDOM Manager but still have plenty of SAN vCPU and Memory available so I am trying to install a new LDOM OS on SAN.
I have exposed the SAN to the... (0 Replies)
Apologies if this is the wrong forum..
I have some LDOMs running on a Sparc server. I copied the disk0 file from one chassis over to another, stopped the ldom on the source system and started it on the 2nd one. All fine. Shut it down and flipped back. We then did a fair bit of work on the... (4 Replies)
Hello,
I am trying to install Solaris 10 on a newly created LDom. Here are the commands I ran to create the LDom:
ldm add-domain ldg2
ldm add-vcpu 8 ldg2
ldm add-memory 2g ldg2
ldm add-vnet vnet2 primary-vsw0 ldg2
ldm add-vdsdev /dev/dsk/c0t5000CCA01535E20Cd0s0 vol2@primary-vds0
ldm... (8 Replies)
Hi,
Our existing environment is having primary domain and 3 guest domains are running over it. See the attached image.
Now we want to add a new primary virtual switch and move LDOM3 to be connected with new primary switch.
So, I am not sure how to achieve this because. If I remove the... (7 Replies)
hello to everyone. im new member here.
i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain.
I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)
I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest.
This question is basically the... (7 Replies)
Discussion started by: Michele31416
7 Replies
LEARN ABOUT DEBIAN
scanssh
scanssh(1) BSD General Commands Manual scanssh(1)NAME
scanssh -- scans the Internet for open proxies and SSH servers
SYNOPSIS
scanssh [-VIERph] [-s scanners,...] [-n ports,...] [-e excludefile] addresses...
DESCRIPTION
ScanSSH scans the given addresses and networks for running services. It mainly allows the detection of open proxies and Internet services.
For known services, ScanSSH will query their version number and displays the results in a list.
The adresses can be either specified as an IPv4 address or an CIDR like IP prefix, ipaddress/masklength. Ports can be appended by adding a
colon at the end of address specification.
Additionally, the following two commands can be prefixed to the address:
random(n[,seed])/ The random command selects random address from the address range specified. The arguments are as follows: n is the number
of address to randomly create in the given network and seed is a seed for the pseudo random number generator.
split(s,e)/ The split command is used to split the address range in several unique components. This can be use to scan from serveral
hosts in parallel. The arguments are as follows: e specifies the number of hosts scanning in parallel and s is the number
of the host this particular scan runs on.
The options are as follows:
-V Causes scanssh to print its version number.
-I Does not send a SSH identification string.
-E Exit the program, if the file containing the addresses for exclusion can not be found.
-R If addresses are generated at random, this flag causes the program to ignore excluded addresses from the exclude file. The
default behaviour is to always exclude addresses.
-p Specifies that ScanSSH should operate as a proxy detector. This flag sets the default modes and default scanners to detect
open proxies.
-h Displays the usage of the program.
-n ports,... Specifies the port numbers to scan. Ports are separated by commas. Each specified scanner is run for each port in this
list. The default is 22.
-s scanners Specifies a number of scanners should be executed for each open port. Multiple scanners are separated by commas. The fol-
lowing scanners are currently supported:
ssh Finds versions for SSH, Web and SMTP servers.
socks5 Detects if a SOCKS V5 proxy is running on the port.
socks4 Detects if a SOCKS V4 proxy is running on the port.
http-proxy Detects a HTTP get proxy.
http-connect Detects a HTTP connect proxy.
telnet-proxy Detects telnet based proxy servers.
-e excludefile Specifies the file that contains the addresses to be excluded from the scan. The syntax is the same as for the addresses on
the command line.
The output from scanssh contains only IP addresses. However, the IP addresses can be converted to names with the logresolve(8) tool included
in the Apache webserver.
EXAMPLES
The following command scans the class C network 10.0.0.0 - 10.0.0.255 for open proxies:
scanssh -p 10.0.0.0/24
The next command scans for ssh servers on port 22 only:
scanssh -n 22 -s ssh 192.168.0.0/16
The following command can be used in a parallel scan. Two hosts scan the specified networks randomly, where this is the first host:
scanssh 'random(0,rsd)/split(1,2)/(192.168.0.0/16 10.1.0.0/24):22,80'
BUGS
At the moment, scanssh leaves a one line entry in the log file of the ssh server. It is probably not possible to avoid that.
BSD July 17, 2000 BSD