Your T4 box has 3 IP addresses on three interface, from one which is VNIC net1 net0 vnic0
In one point in time, these addresses have been configured...
If you wish to remove the mentioned address found in this output :
Execute the following on the hypervisor via SP or connected to any other address but 78 via ssh :
The system is complaining for duplicate address since you have one defined on VNIC in hypervisor and same inside LDOM.
Hope that helps
Regards
Peasant.
These 2 Users Gave Thanks to Peasant For This Post:
Hi,
I have issues installing Solaris into a LDom using a Solaris10u5/08 DVD. I have been troubleshooting for the past 2 days and I still cannot get it up.
Here is the logs:
root@eld-app2# ldm add-vdsdev /cdrom/sol_10_508_sparc/s0 cdrom0@primary-vds0
root@eld-app2# ldm add-vdisk cdrom0... (4 Replies)
Hi Gurus
I am in a strange situation.
I have a SUN sparc server . The server was having an IP say X..... (this IP X is now being used by another server)..... I have just installed fresh solaris 9 OS on the same server and given new IP say Y.
I also configured probe based IPMP with ce0 and... (2 Replies)
I have viewed a few previous posts regarding this, but none of them quite described or worked with my issue.
I am out of local disk space on my LDOM Manager but still have plenty of SAN vCPU and Memory available so I am trying to install a new LDOM OS on SAN.
I have exposed the SAN to the... (0 Replies)
Apologies if this is the wrong forum..
I have some LDOMs running on a Sparc server. I copied the disk0 file from one chassis over to another, stopped the ldom on the source system and started it on the 2nd one. All fine. Shut it down and flipped back. We then did a fair bit of work on the... (4 Replies)
Hello,
I am trying to install Solaris 10 on a newly created LDom. Here are the commands I ran to create the LDom:
ldm add-domain ldg2
ldm add-vcpu 8 ldg2
ldm add-memory 2g ldg2
ldm add-vnet vnet2 primary-vsw0 ldg2
ldm add-vdsdev /dev/dsk/c0t5000CCA01535E20Cd0s0 vol2@primary-vds0
ldm... (8 Replies)
Hi,
Our existing environment is having primary domain and 3 guest domains are running over it. See the attached image.
Now we want to add a new primary virtual switch and move LDOM3 to be connected with new primary switch.
So, I am not sure how to achieve this because. If I remove the... (7 Replies)
hello to everyone. im new member here.
i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain.
I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)
I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest.
This question is basically the... (7 Replies)
Discussion started by: Michele31416
7 Replies
LEARN ABOUT X11R4
chcpu
CHCPU(8) System Administration CHCPU(8)NAME
chcpu - configure CPUs
SYNOPSIS
chcpu -c|-d|-e|-g cpu-list
chcpu -p mode
chcpu -r|-h|-V
DESCRIPTION
chcpu can modify the state of CPUs. It can enable or disable CPUs, scan for new CPUs, change the CPU dispatching mode of the underlying
hypervisor, and request CPUs from the hypervisor (configure) or return CPUs to the hypervisor (deconfigure).
Some options have a cpu-list argument. Use this argument to specify a comma-separated list of CPUs. The list can contain individual CPU
addresses or ranges of addresses. For example, 0,5,7,9-11 makes the command applicable to the CPUs with the addresses 0, 5, 7, 9, 10, and
11.
OPTIONS -c, --configure cpu-list
Configure the specified CPUs. Configuring a CPU means that the hypervisor takes a CPU from the CPU pool and assigns it to the vir-
tual hardware on which your kernel runs.
-d, --disable cpu-list
Disable the specified CPUs. Disabling a CPU means that the kernel sets it offline.
-e, --enable cpu-list
Enable the specified CPUs. Enabling a CPU means that the kernel sets it online. A CPU must be configured, see -c, before it can be
enabled.
-g, --deconfigure cpu-list
Deconfigure the specified CPUs. Deconfiguring a CPU means that the hypervisor removes the CPU from the virtual hardware on which
the Linux instance runs and returns it to the CPU pool. A CPU must be offline, see -d, before it can be deconfigured.
-p, --dispatch mode
Set the CPU dispatching mode (polarization). This option has an effect only if your hardware architecture and hypervisor support
CPU polarization. Available modes are:
horizontal The workload is spread across all available CPUs.
vertical The workload is concentrated on few CPUs.
-r, --rescan
Trigger a rescan of CPUs. After a rescan, the Linux kernel recognizes the new CPUs. Use this option on systems that do not auto-
matically detect newly attached CPUs.
-V, --version
Display version information and exit.
-h, --help
Display help text and exit.
RETURN CODES
chcpu has the following return codes:
0 success
1 failure
64 partial success
AUTHOR
Heiko Carstens <heiko.carstens@de.ibm.com>
COPYRIGHT
Copyright IBM Corp. 2011
SEE ALSO lscpu(1)AVAILABILITY
The chcpu command is part of the util-linux package and is available from Linux Kernel Archive <https://www.kernel.org/pub/linux/utils
/util-linux/>.
util-linux July 2014 CHCPU(8)