Sponsored Content
Top Forums UNIX for Beginners Questions & Answers Exit1 not to report failure in controlM Post 303043398 by Mi4304 on Monday 27th of January 2020 01:43:54 PM
Old 01-27-2020
Thank you for response,

This is Shell script bash, placed in server and calling the from command line of controlM job.
this for validating the number of job records between two tables. if there is no records on the second table script will end with exit1 and controlM is throwing as job failure so trying to make this to end with exit0 but not to end with failure
 

10 More Discussions You Might Find Interesting

1. Programming

ld failure

Hi, I am using gmake to compile a c program with a makefile. The make file runs ld. I get the following error jsh1035c:/users/egate453/admegate/kapil/samples $ gmake -e -f GNUmakefile queue_c gmake -f ./GNUmakefile queue_c in_objdir=1 build_root=/users/egate453/admegate/kapil/samples... (2 Replies)
Discussion started by: handak9
2 Replies

2. SCO

Raid5 Failure

Forgive me, I do not know much about RAID so I'm going to be as detailed as possible. This morning, our server's alarm was going. I found that one of our drives have failed. (we have 3) It is an Adaptec ATA RAID 2400A controller I'm purchasing a new SCSI drive today. My questions: ... (2 Replies)
Discussion started by: gseyforth
2 Replies

3. UNIX for Advanced & Expert Users

sudo comand with ControlM

I'm trying to change the user Id that the script is running under. I tried the sudo comand but the job was submitted under ControlM and it seems that controlM is not allowing the user id to change. I have included the job output below. The sudo comand was suppose to set the user id to "DWSOLAP"... (3 Replies)
Discussion started by: u156531
3 Replies

4. UNIX for Advanced & Expert Users

su failure

Usually when su rejects an attempt to switch user it responds with "Sorry" but with a certain username on some unix servers the response is "Killed". I'm guessing the su accepted the username/password but refused to spawn child shell with the specified username. What's causing this and what has to... (8 Replies)
Discussion started by: twk
8 Replies

5. UNIX for Dummies Questions & Answers

Identify File with ControlM Characters

Dear Members, I have a file which contains ControlM characters in it. I need a command by the means of which i should be able to identify if a file has controlM characters. How can this be achieved. Thanks Sandeep (4 Replies)
Discussion started by: sandeep_1105
4 Replies

6. Solaris

DMA failure ?

Our Solaris was hung yesterday, and dmesg show that, nxge3 : <== nxge_m_start: initialization failed nxge2 : nxge_dma_mem_alloc:ddi_dma_mem_alloc kmem alloc failed nxge2 : nxge_alloc_rx_buf_dma: Alloc Failed: dma 9 size_index 10 size requested 4194304 Does it mean the DMA failure ? How... (5 Replies)
Discussion started by: dehetoxic
5 Replies

7. Shell Programming and Scripting

Sftp failure

Hello, Sometimes when i execute my shell that makes sftp it gives me this error: Couldn't close file: Failure. What does it mean?, how can i make sure it will do ok?. Bye (2 Replies)
Discussion started by: rubber08
2 Replies

8. Red Hat

NT_STATUS_LOGON FAILURE

I am configuring Samba on one of my vmware.when i put smbclient -L local its showing error message : NT_STATUS_LOGON failure.I found that when i remove "Encrypted password entry from smb.conf" it works. pls help me ---------- Post updated at 08:39 PM ---------- Previous update was at 07:11 PM... (0 Replies)
Discussion started by: Vaibhav.T
0 Replies

9. UNIX for Dummies Questions & Answers

boot up failure unix sco after power failure

hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies

10. Filesystems, Disks and Memory

MDADM Failure - where it came from?

Hello, i have a system with 6 sata3 seagate st3000dm01 disks running on stable Debian with software raid mdadm. i have md0 for root and md1 for swap and md2 for the files. i now want to add one more disk = sdh4 for md2 but i got this errors: The new disk is connected to an 4 port sata... (7 Replies)
Discussion started by: Sunghost
7 Replies
NWPJMV(1)							      nwpjmv								 NWPJMV(1)

NAME
nwpjvm - Move print job to Unix queue SYNOPSIS
nwpjmv [ -S server ] [ -h ] [ -U user name ] [ -P password | -n ] [ -C ] [ -q queue name ] [ -c command ] [ -j job number ] [ -d ] DESCRIPTION
nwpjmv is a program that connects to print queues on NetWare servers and moves a designated print job to a Unix queue. OPTIONS
-h -h is used to print out a short help text. -S server server is the name of the server you want to use. -U user user is the print server name at the server. -P password password is the password to use for the print server at the server. If neither -n nor -P are given, and the user has no open connection to the server, pserver prompts for a password. -n -n should be given if the print server does not require a password. -C By default, passwords are converted to uppercase before they are sent to the server, because most servers require this. You can turn off this conversion by -C. -q queue name queue name is the name of the print queue you want to service. -c command nwpjmv removes the designated job from the Novell queue and feeds the job file to stdin. command is the printing command that is exe- cuted for each job. The default command is 'lpr'. You can insert several flags into the command, preceded by %. These are replaced with values retrieved from the queue structure for the print job. %u: This field will be replaced by the name of the user who posted this print job. %d: This field will be replaced by the job description field of this print job. -j job number This designates the ID number of the print job to be moved. -d causes extra error messages to be logged. SEE ALSO
nwclient(5), slist(1), pqlist(1), ncpmount(8), ncpumount(8), pserver(1) CREDITS
nwpjmv was written by Bruno Browning (bruno@lss.wisc.edu) based on pserver by Volker Lendecke (lendecke@math.uni-goettingen.de) nwpjmv 03/15/2003 NWPJMV(1)
All times are GMT -4. The time now is 08:20 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy