01-27-2020
Thank you for response,
This is Shell script bash, placed in server and calling the from command line of controlM job.
this for validating the number of job records between two tables. if there is no records on the second table script will end with exit1 and controlM is throwing as job failure so trying to make this to end with exit0 but not to end with failure
10 More Discussions You Might Find Interesting
1. Programming
Hi,
I am using gmake to compile a c program with a makefile. The make file runs ld. I get the following error
jsh1035c:/users/egate453/admegate/kapil/samples $ gmake -e -f GNUmakefile queue_c
gmake -f ./GNUmakefile queue_c in_objdir=1 build_root=/users/egate453/admegate/kapil/samples... (2 Replies)
Discussion started by: handak9
2 Replies
2. SCO
Forgive me, I do not know much about RAID so I'm going to be
as detailed as possible.
This morning, our server's alarm was going. I found that one
of our drives have failed. (we have 3)
It is an Adaptec ATA RAID 2400A controller
I'm purchasing a new SCSI drive today. My questions:
... (2 Replies)
Discussion started by: gseyforth
2 Replies
3. UNIX for Advanced & Expert Users
I'm trying to change the user Id that the script is running under. I tried the sudo comand but the job was submitted under ControlM and it seems that controlM is not allowing the user id to change. I have included the job output below. The sudo comand was suppose to set the user id to "DWSOLAP"... (3 Replies)
Discussion started by: u156531
3 Replies
4. UNIX for Advanced & Expert Users
Usually when su rejects an attempt to switch user it responds with "Sorry" but with a certain username on some unix servers the response is "Killed". I'm guessing the su accepted the username/password but refused to spawn child shell with the specified username. What's causing this and what has to... (8 Replies)
Discussion started by: twk
8 Replies
5. UNIX for Dummies Questions & Answers
Dear Members,
I have a file which contains ControlM characters in it.
I need a command by the means of which i should be able to identify if a file has controlM characters.
How can this be achieved.
Thanks
Sandeep (4 Replies)
Discussion started by: sandeep_1105
4 Replies
6. Solaris
Our Solaris was hung yesterday, and dmesg show that,
nxge3 : <== nxge_m_start: initialization failed
nxge2 : nxge_dma_mem_alloc:ddi_dma_mem_alloc kmem alloc failed
nxge2 : nxge_alloc_rx_buf_dma: Alloc Failed: dma 9 size_index 10 size requested 4194304
Does it mean the DMA failure ? How... (5 Replies)
Discussion started by: dehetoxic
5 Replies
7. Shell Programming and Scripting
Hello,
Sometimes when i execute my shell that makes sftp it gives me this error:
Couldn't close file: Failure.
What does it mean?, how can i make sure it will do ok?.
Bye (2 Replies)
Discussion started by: rubber08
2 Replies
8. Red Hat
I am configuring Samba on one of my vmware.when i put smbclient -L local its showing error message : NT_STATUS_LOGON failure.I found that when i remove "Encrypted password entry from smb.conf" it works.
pls help me
---------- Post updated at 08:39 PM ---------- Previous update was at 07:11 PM... (0 Replies)
Discussion started by: Vaibhav.T
0 Replies
9. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies
10. Filesystems, Disks and Memory
Hello,
i have a system with 6 sata3 seagate st3000dm01 disks running on stable Debian with software raid mdadm. i have md0 for root and md1 for swap and md2 for the files. i now want to add one more disk = sdh4 for md2 but i got this errors:
The new disk is connected to an 4 port sata... (7 Replies)
Discussion started by: Sunghost
7 Replies