Yes, I understand this metric. It is set to 3600. NS are pointed on Network Solutions, which says their minimum is also 3600. From their website - "Network Solutions® allows a minimum of 3600 (1 hour)"
... and there was absolutely nothing installed except fedora and ssh. I used yum to install vsftp and httpd, both start and ps shows they're running, and yet I can't connect with either of them. Where on earth or in redhat do I begin looking to unravel this one? I've overseen a server before but... (3 Replies)
hi gurus,
need to check other than the hosts file, what else i need to change after we have changed the domain name in our company. currently, we are using olddnsname.com and will change it to newdnsname.com. i am not sure where else in solaris i need to take a look.
please advise.
thank... (4 Replies)
Hello,
I'm using CentOS 5.3, and I connect to a VPN in order to work. The problem is that I'm constantly accessing things on the local network and the remote network. But once I'm connected to the VPN I can't access local addresses by name, I have to use the ip-address.
What I'd like is to... (4 Replies)
Hi everybody,
for revolving local host name of my network, I set up an dns server to solve my problem, but til now, nothing happen when I ping a hostname, but work on IP. Can you help me to correct the configuration. Here is all my settings:
Voici mes fichiers de configuration:
-... (2 Replies)
Looking for a recommendation -
I'm looking for a reliable domain control panel (like cPanel) that is open source, and I can customize it do work into my work flow.
Essentially, I need new users to be able to create a new account so that
a) a new subdomain is created, or
b) a full domain... (0 Replies)
Hi, Im trying to change my domain name in my solaris as below:
but it keeps coming back to be "unknown"
Im changing /etc/inet/hosts.e1000g0\and also
i added one line to /etc/nodename
my vm (i have my solaris on VM)ip address is 192.168.1.103 and Im putting solar as a name for it
... (2 Replies)
Hello to all,
May you help saying me how to flush a specific domain in Linux SunOS5
I know the command rndc is to flush DNS cache, but I would like to know:
1- How to do a flush only on specific domain
2- How to see the content of DNS Resolver cache (similar to info given by IPCONFIG... (2 Replies)
I have read many tutorials on bind and i understand the A,MX, CNAME records.
Internally, on a LAN we can install bind and create all these records and we can tell all PC and servers to use this bind as DNS server.that's fine.
On the Internet, when we have purchased a valid domain like... (5 Replies)
In my /etc/resolv.conf file there is domain name defined. But when I do nslookup the domain name is not appended. Why? (18 Replies)
Discussion started by: broy32000
18 Replies
LEARN ABOUT DEBIAN
smokeping_probes_dns
Smokeping_probes_DNS(3) SmokePing Smokeping_probes_DNS(3)NAME
Smokeping::probes::DNS - Name Service Probe for SmokePing
SYNOPSIS
*** Probes ***
+DNS
binary = /usr/bin/dig # mandatory
forks = 5
offset = 50%
step = 300
timeout = 15
# The following variables can be overridden in each target section
lookup = www.example.org
pings = 5
server = ns1.someisp.net
# [...]
*** Targets ***
probe = DNS # if this should be the default probe
# [...]
+ mytarget
# probe = DNS # if the default probe is something else
host = my.host
lookup = www.example.org
pings = 5
server = ns1.someisp.net
DESCRIPTION
Integrates dig as a probe into smokeping. The variable binary must point to your copy of the dig program. If it is not installed on your
system yet, you should install bind-utils >= 9.0.0.
The Probe asks the given host n-times for it's name. Where n is the amount specified in the config File.
VARIABLES
Supported probe-specific variables:
binary
The location of your dig binary.
Example value: /usr/bin/dig
This setting is mandatory.
forks
Run this many concurrent processes at maximum
Example value: 5
Default value: 5
offset
If you run many probes concurrently you may want to prevent them from hitting your network all at the same time. Using the probe-
specific offset parameter you can change the point in time when each probe will be run. Offset is specified in % of total interval, or
alternatively as 'random', and the offset from the 'General' section is used if nothing is specified here. Note that this does NOT
influence the rrds itself, it is just a matter of when data acqusition is initiated. (This variable is only applicable if the variable
'concurrentprobes' is set in the 'General' section.)
Example value: 50%
step
Duration of the base interval that this probe should use, if different from the one specified in the 'Database' section. Note that the
step in the RRD files is fixed when they are originally generated, and if you change the step parameter afterwards, you'll have to
delete the old RRD files or somehow convert them. (This variable is only applicable if the variable 'concurrentprobes' is set in the
'General' section.)
Example value: 300
timeout
How long a single 'ping' takes at maximum
Example value: 15
Default value: 5
Supported target-specific variables:
lookup
Name of the host to look up in the dns.
Example value: www.example.org
pings
How many pings should be sent to each target, if different from the global value specified in the Database section. Note that the
number of pings in the RRD files is fixed when they are originally generated, and if you change this parameter afterwards, you'll have
to delete the old RRD files or somehow convert them.
Example value: 5
server
Name of the dns server to use.
Example value: ns1.someisp.net
AUTHORS
Igor Petrovski <pigor@myrealbox.com>,
Carl Elkins <carl@celkins.org.uk>,
Andre Stolze <stolze@uni-muenster.de>,
Niko Tyni <ntyni@iki.fi>,
Chris Poetzel<cpoetzel@anl.gov>
2.6.8 2013-03-17 Smokeping_probes_DNS(3)