01-24-2020
Look for an update of the driver/firmware.
You bought them from Oracle? Contact Oracle support!
This User Gave Thanks to MadeInGermany For This Post:
10 More Discussions You Might Find Interesting
1. Solaris
Has anyone configured one of these things, I cant seem to find any documentation on sunsolve, I want to verify that it is up and running... (1 Reply)
Discussion started by: csaunders
1 Replies
2. Solaris
Hi all,
I have a compatibly issues with a new hardware
My config is the following one :
Solaris 10
V490 Hardware
2 X HBA Qlogic 2310f cards
An HP EVA 5000 for storage ...
Veritas VxVM 4.1 MP1
When I reboot my server, VxVM is trying to mount/use the volume before it's... (0 Replies)
Discussion started by: unclefab
0 Replies
3. HP-UX
I need information what maximum error level on FC card need clasification of critical level (SAN mass storidge)
Please write screenshot from utility fcutil whith test option.
Pawel (0 Replies)
Discussion started by: pawel_ul
0 Replies
4. UNIX for Advanced & Expert Users
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (3 Replies)
Discussion started by: ronbarak
3 Replies
5. Solaris
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (4 Replies)
Discussion started by: ronbarak
4 Replies
6. Solaris
I installed a FC array for the first time and everything looks OK
in mpathadm, cfgadm, but I don't know what to do next.
# stmsboot -L
non-STMS device name STMS device name
------------------------------------------------------------------
/dev/rdsk/c2t1d0 ... (3 Replies)
Discussion started by: photon
3 Replies
7. Solaris
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies
8. Solaris
Hello all,
how can i see configured fc tapes in solaris system and how can i install a new fc shared tape device , thanks
Best Regards (2 Replies)
Discussion started by: bogacd
2 Replies
9. IP Networking
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies
10. Solaris
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
LEARN ABOUT SUSE
apache::session::store::oracle
Session::Store::Oracle(3) User Contributed Perl Documentation Session::Store::Oracle(3)
NAME
Apache::Session::Store::Oracle - Store persistent data in a Oracle database
SYNOPSIS
use Apache::Session::Store::Oracle;
my $store = new Apache::Session::Store::Oracle;
$store->insert($ref);
$store->update($ref);
$store->materialize($ref);
$store->remove($ref);
DESCRIPTION
Apache::Session::Store::Oracle fulfills the storage interface of Apache::Session. Session data is stored in a Oracle database.
SCHEMA
To use this module, you will need at least these columns in a table called 'sessions':
id varchar2(32) # or however long your session IDs are.
a_session long
To create this schema, you can execute this command using the sqlplus program:
CREATE TABLE sessions (
id varchar2(32) not null primary key,
a_session long
);
If you use some other command, ensure that there is a unique index on the table's id column.
CONFIGURATION
The module must know what datasource, username, and password to use when connecting to the database. These values can be set using the
options hash (see Apache::Session documentation). The options are DataSource, UserName, and Password.
Example:
tie %hash, 'Apache::Session::Oracle', $id, {
DataSource => 'dbi:Oracle:database',
UserName => 'database_user',
Password => 'K00l'
};
Instead, you may pass in an already-opened DBI handle to your database.
tie %hash, 'Apache::Session::Oracle', $id, {
Handle => $dbh
};
The last option is LongReadLen, which specifies the maximum size of the session object. If not supplied, the default maximum size is 8 KB.
AUTHOR
This modules was written by Jeffrey William Baker <jwbaker@acm.org>
A fix for the commit policy was contributed by Michael Schout <mschout@gkg.net>
SEE ALSO
Apache::Session, Apache::Session::Store::DBI
perl v5.12.1 2007-09-28 Session::Store::Oracle(3)