I running below script from controlM and job is reporting as failure everyday so i tried to change the if exitstatus=1 (send only email) but not to end as a job is failed. can you let me know where i have to change this script to make the script not to fail but instead send email and complete successfully
====
Hi,
I am using gmake to compile a c program with a makefile. The make file runs ld. I get the following error
jsh1035c:/users/egate453/admegate/kapil/samples $ gmake -e -f GNUmakefile queue_c
gmake -f ./GNUmakefile queue_c in_objdir=1 build_root=/users/egate453/admegate/kapil/samples... (2 Replies)
Forgive me, I do not know much about RAID so I'm going to be
as detailed as possible.
This morning, our server's alarm was going. I found that one
of our drives have failed. (we have 3)
It is an Adaptec ATA RAID 2400A controller
I'm purchasing a new SCSI drive today. My questions:
... (2 Replies)
I'm trying to change the user Id that the script is running under. I tried the sudo comand but the job was submitted under ControlM and it seems that controlM is not allowing the user id to change. I have included the job output below. The sudo comand was suppose to set the user id to "DWSOLAP"... (3 Replies)
Usually when su rejects an attempt to switch user it responds with "Sorry" but with a certain username on some unix servers the response is "Killed". I'm guessing the su accepted the username/password but refused to spawn child shell with the specified username. What's causing this and what has to... (8 Replies)
Dear Members,
I have a file which contains ControlM characters in it.
I need a command by the means of which i should be able to identify if a file has controlM characters.
How can this be achieved.
Thanks
Sandeep (4 Replies)
Hello,
Sometimes when i execute my shell that makes sftp it gives me this error:
Couldn't close file: Failure.
What does it mean?, how can i make sure it will do ok?.
Bye (2 Replies)
I am configuring Samba on one of my vmware.when i put smbclient -L local its showing error message : NT_STATUS_LOGON failure.I found that when i remove "Encrypted password entry from smb.conf" it works.
pls help me
---------- Post updated at 08:39 PM ---------- Previous update was at 07:11 PM... (0 Replies)
Hello,
i have a system with 6 sata3 seagate st3000dm01 disks running on stable Debian with software raid mdadm. i have md0 for root and md1 for swap and md2 for the files. i now want to add one more disk = sdh4 for md2 but i got this errors:
The new disk is connected to an 4 port sata... (7 Replies)
Discussion started by: Sunghost
7 Replies
LEARN ABOUT DEBIAN
dh_installinit
DH_INSTALLINIT(1) Debhelper DH_INSTALLINIT(1)NAME
dh_installinit - install init scripts and/or upstart jobs into package build directories
SYNOPSIS
dh_installinit [debhelperoptions] [--name=name] [-n] [-R] [-r] [-d] [--params]
DESCRIPTION
dh_installinit is a debhelper program that is responsible for installing init scripts with associated defaults files, as well as upstart
job files into package build directories.
It also automatically generates the postinst and postrm and prerm commands needed to set up the symlinks in /etc/rc*.d/ to start and stop
the init scripts.
FILES
debian/package.init
If this exists, it is installed into etc/init.d/package in the package build directory.
debian/package.default
If this exists, it is installed into etc/default/package in the package build directory.
debian/package.upstart
If this exists, it is installed into etc/init/package.conf in the package build directory.
OPTIONS -n, --noscripts
Do not modify postinst/postrm/prerm scripts.
-o, --onlyscripts
Only modify postinst/postrm/prerm scripts, do not actually install any init script, default files, or upstart job. May be useful if the
init script or upstart job is shipped and/or installed by upstream in a way that doesn't make it easy to let dh_installinit find it.
-R, --restart-after-upgrade
Do not stop the init script until after the package upgrade has been completed. This is different than the default behavior, which
stops the script in the prerm, and starts it again in the postinst.
This can be useful for daemons that should not have a possibly long downtime during upgrade. But you should make sure that the daemon
will not get confused by the package being upgraded while it's running before using this option.
-r, --no-restart-on-upgrade
Do not stop init script on upgrade.
--no-start
Do not start the init script on install or upgrade, or stop it on removal. Only call update-rc.d. Useful for rcS scripts.
-d, --remove-d
Remove trailing d from the name of the package, and use the result for the filename the upstart job file is installed as in etc/init/ ,
and for the filename the init script is installed as in etc/init.d and the default file is installed as in etc/default/ . This may be
useful for daemons with names ending in d. (Note: this takes precedence over the --init-script parameter described below.)
-uparams --update-rcd-params=params
-- params
Pass params to update-rc.d(8). If not specified, defaults will be passed to update-rc.d(8).
--name=name
Install the init script (and default file) as well as upstart job file using the filename name instead of the default filename, which
is the package name. When this parameter is used, dh_installinit looks for and installs files named debian/package.name.init,
debian/package.name.default and debian/package.name.upstart instead of the usual debian/package.init, debian/package.default and
debian/package.upstart.
--init-script=scriptname
Use scriptname as the filename the init script is installed as in etc/init.d/ (and also use it as the filename for the defaults file,
if it is installed). If you use this parameter, dh_installinit will look to see if a file in the debian/ directory exists that looks
like package.scriptname and if so will install it as the init script in preference to the files it normally installs.
This parameter is deprecated, use the --name parameter instead. This parameter is incompatible with the use of upstart jobs.
--error-handler=function
Call the named shell function if running the init script fails. The function should be provided in the prerm and postinst scripts,
before the #DEBHELPER# token.
NOTES
Note that this command is not idempotent. dh_prep(1) should be called between invocations of this command. Otherwise, it may cause multiple
instances of the same text to be added to maintainer scripts.
SEE ALSO debhelper(7)
This program is a part of debhelper.
AUTHORS
Joey Hess <joeyh@debian.org>
Steve Langasek <steve.langasek@canonical.com>
9.20120909 2012-04-10 DH_INSTALLINIT(1)