01-17-2020
you can connect your fibre adapter to as many VMs as you want - you just need to configure the amount of virtuals you will probably need in the profile of the vios and then you just map
8 More Discussions You Might Find Interesting
1. AIX
Hey
May be a dumb question
Can I use a SPOT which is at 5.3 TL6 to boot an LPAR (with 5.3 TL8) in to maintenance mode? Will it work ?
Is it mandatory that SPOT should be of same or higher version in such case?
Bala (1 Reply)
Discussion started by: balaji_prk
1 Replies
2. Shell Programming and Scripting
I am trying to script and came up with a conclusion that I need a do while loop in my statement. I am stuck with the
do while syntax. I need to use it alongwith the if then else statement. Can I use it is a big question? I actually need to get all the files
that are there from within run_dt to... (1 Reply)
Discussion started by: aronmelon
1 Replies
3. Shell Programming and Scripting
1.Write an automated shell program(s) that can create, monitor the log files and report the issues for matching pattern.
(i) Conditions for creating log files.
Log file is created with date (example 2010_03_27.log). If the log file size is 10 Mb for a particular day then automatically the log... (3 Replies)
Discussion started by: praveen12
3 Replies
4. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
5. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
6. AIX
Hi All,
I have a p520 box running 3 LPARs, 1 x VIOS, 1 x AIX 6.1 and 1 x AIX 7.1 and no HMC, all configuration is performed via VIOS/IVM
Until recently the box did not have the AIX7.1 LPAR and everything was fine with the box.
We needed to use AIX 7.1 for a new project, so I created a... (11 Replies)
Discussion started by: KevB
11 Replies
7. Shell Programming and Scripting
Hi All,
I have a source file with data
Name ~ Groups
Muni~abc,was,USA_ax,123
Chaitanya~USA_12,was
Balaji~123,xyz,was
Ramu~123,xyz
From the second column i want to extract only the groups that matches the pattern 'USA_%' or if the group = 'was', and ignore any other columns.
... (8 Replies)
Discussion started by: morbid_angel
8 Replies
8. UNIX for Dummies Questions & Answers
Please help in creating script for below requirement.
I will be running 1 command and will get below entries in a text file say file44.txt
*******************************
DFDL1005 06:30 00:05
ABFL2003 10/22 01:10
CFTL1256 10/24 00:10
10/25 09:20 PM
********************************
.... (3 Replies)
Discussion started by: Vinay_3308
3 Replies
LEARN ABOUT DEBIAN
setether
SETETHER(8) System Manager's Manual SETETHER(8)
NAME
setether - Set the ethernet address for use with DECnet
SYNOPSIS
setether <if> [<if>...]|all [options]
DESCRIPTION
Set ethernet MAC address on ethernet adaptors
This script should be run at system startup. It will change the ethernet hardware (MAC) address of any or all ethernet interfaces to match
the DECnet node address. DECnet requires that the MAC address of all ethernet adaptors running the protocol be set approriately. If you do
not run setether then you must change the ethernet address in some other way for DECnet to work.
By default no ethernet interfaces will have their MAC addresses changed by setether, if you specify all then all interfaces name eth* will
be changed, otherwise a list of interface names can be specified. setether will enable (UP) all interfaces it changes the MAC addresses
of.
(2.4 only) The first interface specified on the command-line will also be made the default interface for DECnet operations (ie attempts to
contact nodes not in the neighbour table will be done over this interface).
This script must be run with the interface inactive, it is normally run from /etc/init.d/decnet before TCP/IP starts up.
EXAMPLES
set the MAC address of eth0.
# /sbin/setether eth0
set the MAC address of all ethernet interfaces
# /sbin/setether all
HELPFUL HINTS
If you have multiple ethernet cards on your system and they are connected to the the same network you should specify which one you want to
use for DECnet communication on the setether command line, otherwise they will both be given the same MAC address and this is probably not
what you want.
Running DECnet on multiple ethernet interfaces only works under Linux 2.4. If you are running Linux 2.2 then the interface name on the
setether command line must match the one in /etc/decnet.conf(5).
SEE ALSO
decnet.conf(5), dntype(1), dndir(1), dndel(1), dnetd(8), dnping(1)
DECnet utilities March 01 2001 SETETHER(8)