Then, on AIX lpar (vio client) create new virtual ethernet. Then use smitty tcpip to configure the IP.
I can end up pinging the aix lpar
Regarding your question, this frame is no longer used in prod, so I took it as my test machine with few lpar and 1 VIOS only.
I have internal disks(SAS). But I wonder, if I have only 1 physical FC connected with LUN, Could I reuse it also for another virtual FCs to connect to other Lun? or I need another physical FC to do that?
Hey
May be a dumb question
Can I use a SPOT which is at 5.3 TL6 to boot an LPAR (with 5.3 TL8) in to maintenance mode? Will it work ?
Is it mandatory that SPOT should be of same or higher version in such case?
Bala (1 Reply)
I am trying to script and came up with a conclusion that I need a do while loop in my statement. I am stuck with the
do while syntax. I need to use it alongwith the if then else statement. Can I use it is a big question? I actually need to get all the files
that are there from within run_dt to... (1 Reply)
1.Write an automated shell program(s) that can create, monitor the log files and report the issues for matching pattern.
(i) Conditions for creating log files.
Log file is created with date (example 2010_03_27.log). If the log file size is 10 Mb for a particular day then automatically the log... (3 Replies)
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Hi All,
I have a p520 box running 3 LPARs, 1 x VIOS, 1 x AIX 6.1 and 1 x AIX 7.1 and no HMC, all configuration is performed via VIOS/IVM
Until recently the box did not have the AIX7.1 LPAR and everything was fine with the box.
We needed to use AIX 7.1 for a new project, so I created a... (11 Replies)
Hi All,
I have a source file with data
Name ~ Groups
Muni~abc,was,USA_ax,123
Chaitanya~USA_12,was
Balaji~123,xyz,was
Ramu~123,xyz
From the second column i want to extract only the groups that matches the pattern 'USA_%' or if the group = 'was', and ignore any other columns.
... (8 Replies)
Please help in creating script for below requirement.
I will be running 1 command and will get below entries in a text file say file44.txt
*******************************
DFDL1005 06:30 00:05
ABFL2003 10/22 01:10
CFTL1256 10/24 00:10
10/25 09:20 PM
********************************
.... (3 Replies)
Discussion started by: Vinay_3308
3 Replies
LEARN ABOUT OPENSOLARIS
mega_sas
mega_sas(7D) Devices mega_sas(7D)NAME
mega_sas - SCSI HBA driver for LSI MegaRAID SAS controller
DESCRIPTION
The mega_sas MegaRAID controller host bus adapter driver is a SCSA-compliant nexus driver that supports the Dell PERC 5/E, 5/i, 6/E and
6/i RAID controllers, the IBM ServeRAID-MR10k SAS/SATA controller and the LSI MegaRAID SAS/SATA 8308ELP, 8344ELP, 84016E, 8408ELP,
8480ELP, 8704ELP, 8704EM2, 8708ELP, 8708EM2, 8880EM2 and 8888ELP series of controllers.
Supported RAID features include RAID levels 0, 1, 5, and 6, RAID spans 10, 50 and 60, online capacity expansion (OCE), online RAID level
migration (RLM), auto resume after loss of system power during arrays, array rebuild or reconstruction (RLM) and configurable stripe size
up to 1MB. Additional supported RAID features include check consistency for background data integrity, patrol read for media scanning and
repairing, 64 logical drive support, up to 64TB LUN support, automatic rebuild and global and dedicated hot spare support.
CONFIGURATION
The mega_sas.conf file contains no user configurable parameters. Please configure your hardware through the related BIOS utility or the
MegaCli configuration utility. If you want to install to a drive attached to a mega_sas HBA, you should create the virtual drive first
from the BIOS before running the Solaris install. You can obtain the MegaCli utility from the LSI website.
The mega_sas device can support up to 64 virtual disks. Note that BIOS numbers the virtual disks as 1 through 64, however in the Solaris
operating environment virtual disks are numbered from 0 to 63. Also note that SAS and SATA drives cannot be configured into the same vir-
tual disk.
KNOWN PROBLEMS AND LIMITATIONS
The mega_sas driver does not support the LSI MegaRAID SAS 8204ELP, 8204XLP, 8208ELP, and 8208XLP controllers.
FILES
/kernel/drv/mega_sas 32-bit ELF kernel module. (x86)
/kernel/drv/amd64/mega_sas 64-bit kernel module. (x86)
/kernel/drv/mega_sas.conf Driver configuration file (contains no user-configurable options).
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86-based systems |
+-----------------------------+-----------------------------+
|Availability |SUNWmegasas |
+-----------------------------+-----------------------------+
|Interface stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO prtconf(1M), attributes(5), sata(7D), scsi_hba_attach_setup(9F), scsi_sync_pkt(9F), scsi_transport(9F), scsi_inquiry(9S), scsi_device(9S),
scsi_pkt(9S)
Small Computer System Interface-2 (SCSI-2)
SunOS 5.11 14 Aug 2008 mega_sas(7D)
01-16-2020
