It depends quite what you are looking for. Do any of these help (sorry but I no longer have access to AIX so I'm a bit rusty!)
What are the metrics you are looking for? Is it the LPAR view of the assigned disk to the size of the disk that is owned by the hardware as a whole? The LPAR will not see that.
I hope that these suggestions give you something.
Robin
Thank Robin, I would like to check at the physical hardware console, not from LPAR, have not LPAR right now.
--- Post updated at 06:13 AM ---
Quote:
Originally Posted by zxmaus
from the hardware itself, you cannot see the disks - you can only see the controllers, not what is attached to them.
As part of the SMS menu you can see the disks and sizes if you query the controllers - or when you install AIX as you have to select a suitable disks for the installation - with location code.
If you have AIX already installed, run these commands.
to find your SAS disks, run
to figure out the disk size of said disks use
Hi Zxmaus,
I understand now that from physical hardware Power Machine we cannot check the disk and size.
Still have 1 thing to ask, for SAS disk, I see it is part of raid controller. The disk is called pdisk. After configuring raid, it becomes hdisk which AIX can see. The question is, if in the first time, we assign the controller and its disks to LPAR to install AIX. How can we configure the raid before AIX OS can see these disks?
I have two Unix machines on the network and now one of them are running out of disk but i have alot on the other so i like to mount the disk (or a folder) from the one that has disk and mount it on the other that does not.
How do i do that? Is it possible i read the "man mount" but didn't really... (5 Replies)
Hi!!
I am these days working on a project, where I need to know about the disk controllers available in a machine (e.g., 3ware,IBM,etc).
Please, let me know the command by which I can get the information.
thnx,
priyanka (3 Replies)
Hello All,
Can anybody please tell me what is the maximum limit of Physical IBM Power Machine which can be handled by single HMC at a single point of time?
Thanks,
Jenish (1 Reply)
Hello,
I have a quick question regarding POWER HA ( HACMP ) 5.5 ;
I have four ethernet adapters
en0
en1
en2
en3
en0 is configured as BOOT_IP with IP address
all other ethernet adapters are empty en1 / en2 / en3
so when I configure the service IP and start HACMP , the service IP... (2 Replies)
Hi,
Is there an easy way to find the disk-type from the command line or with another api ? sdparm works for SAS but not for SATA, hdparm works for SATA but not SAS.
Thanks (1 Reply)
hi guys,
I don't like the new concept of the power ha 7 cluster with the repository disk and the internal solidb, I really would like to mirror this disk, but the "IBM PowerHA SystemMirror 7.1 for AIX" redbook says, normal lvm operations should not be performed on this disk.
even mirroring the... (0 Replies)
Hi
Is there any native commands or somewhere in the /proc files to get the machine's power consumption? I googled for a while and cannot really find this information
Thanks for your help. (6 Replies)
I need to add a VMware virtual disk to the 99-oracle-asmdevices.rules file but the OS is not assigning a WWID to the disk. It has been fdisk'd and a single partition created.
What TAG inside the file needs to be added? the Program scsi-id does not work for some reason. latest patches... (0 Replies)
Hi,
I have installed the HMC on the VMWare VM. I try to add the power machine (managed system) and asking for a password? So this is the IBM predefined password of Power Machine?
In the VMWare perspective, we can login to ESX host to do some management tasks. But how about the Power machine?... (6 Replies)
OSLevel: 5300-10-02-0943
System Model: IBM,8203-E4A
Power 6
==
Hi!
I replaced a failed pdisk in the raid enclosure as follows,
- rmdev -l 'pdisk18' '-d'
- Replaced it.
- cfgmgr (detected)
- I can see the new drive, with the correct serial #
lscfg -v -l pdisk18
pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
LEARN ABOUT SUNOS
metaimport
metaimport(1M)metaimport(1M)NAME
metaimport - imports disk sets into existing Solaris Volume Manager configurations
SYNOPSIS
metaimport -s setname [-n] [-v] [-f] [disks...]
metaimport -r [disks...]
metaimport -V
metaimport -?
The metaimport command allows the importing of disk sets, including replicated disk sets, into an existing Solaris Volume Manager configu-
ration. Replicated disk sets are disk sets created using remote replication software.
The default Solaris Volume Manager configuration specifies a maximum number of disk sets that can be configured. The metaimport command
fails if importing the disk set would result in exceeding the number of disk sets configured on the system. To increase the number of disk
sets allowed on a system, see the .
Use metaset(1M) or metastat(1M) to view the configuration of the imported set.
You must run metaimport as root.
metaimport requires a functional Solaris Volume Manager configuration before it runs.
The following options are supported:
-f Force the import, even if a quorum of replicas from the imported disk set is not available. This option could
result in corrupt configurations and should only be used when metaimport fails with the "Insufficient quorum
detected; exiting" error. If only a partial disk set is available, this option might be necessary to successfully
import. Some or all data could be corrupted or unavailable when importing a partial set or a set lacking a replica
quorum.
-n Does not actually perform the operation, but shows the output or errors that would have resulted from the opera-
tion, had it been run.
-r Report on the non-configured disk sets found on the system. If no disk device or LUN is specified, metaimport
reports on all non-configured disk sets attached to the system. When the name of one disk is specified, metaimport
reports on the disk set (or virtual LUN) containing the specified disk. If two or more disks are specified, metaim-
port reports on the set (or sets, if they belong to different disk sets) containing the specified disks. If two or
more disks are specified, metaimport reports on the set (or sets, if they belong to different disk sets) containing
the specified disks.
-s setname Specify the disk set name to use when importing. The imported disk set will be called setname, without regard to
the name it may have had on a different system.
-v Verbose. Provides detailed information about the metadb replica location and status.
-V Version information.
-? Display a help message.
Example 1: Importing a Disk Set
The following example creates a disk set called blue and identifies c1t5d0 as a disk containing a state database replica from the disk set
being imported.
# metaimport -s blue c1t5d0
Example 2: Reporting Disk Sets to Import
The following example scans all disks and LUNs attached to the system and configured as part of the system. It scans for disks that could
be part of a disk set to be imported. Components that are already part of the Solaris Volume Manager configuration are ignored.
This use of metaimport provides suggested forms of the metaimport command to use to actually import the disk sets that have been found. You
can specify a component on the command line to reduce the scope of the scan and generate results more quickly.
# metaimport -r
0 Successful completion.
>0 An error occurred.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWmdu |
+-----------------------------+-----------------------------+
|Interface Stability |Stable |
+-----------------------------+-----------------------------+
mdmonitord(1M), metaclear(1M), metadb(1M), metadetach(1M), metahs(1M), metainit(1M), metaoffline(1M), metaonline(1M), metaparam(1M),
metarecover(1M), metareplace(1M), metaroot(1M), metaset(1M), metasync(1M), metattach(1M), md.tab(4), md.cf(4), mddb.cf(4), attributes(5)
16 May 2005 metaimport(1M)