Hi all...
(Apologies for any typos at all.)
This is a step by step _script_ to check if your Arduino is talking to your Linux or Macbook Pro computer using the Terminal...
It works on at least 3 Linux flavours and now the Macbook Pro...
I hope you find it useful as a simple check for... (0 Replies)
This is a very simple starter DEMO to access Arduino Diecimila Board for the
Macbook Pro 13" OSX 10.7.5...
A potentiometer is connected between 5V and Gnd with the wiper connected to
ANALOG IN 0 on the Arduino. This was adjusted to give the Ms and Ls as seen...
I now have DC in for this... (0 Replies)
I am working on a semi-auto detection idea for Arduino for the Scope project.
It does require a little user intervention but minimal.
It works by just responding to two on screen prompts to unplug and plug Arduino
into a USB port.
There are two versions and both work perfectly well and give... (3 Replies)
In my further exploration of Arduino, today I decided to install the arduino-cli on my mac today.
https://github.com/arduino/arduino-cli
I followed the instructions for macOS but when I got to this part:
arduino-cli board list
I got the dreaded "Unknown" Fully Qualified Board Name... (1 Reply)
HI all...
(Apologies for any typos.)
To add to Neo's Arduino subject matter I have decided to upload this in ".zip" format.
Ignore "*.info" files these are AMIGA icons only and also the "HAM" drawer as these are photos in ancient AMIGA HAM modes.
I have noticed that there are current... (6 Replies)
Waiting for more fun Ardunio parts from AliExpress, I decided to test two cheap Chinese Arduino UNO clones.
The Arduino UNO R3 (CH340G) MEGA328P
The Wavgat UNO R3 (CH340G) MEGA328P
Both of these Chinese Ardunio clones sell for about $3 USD, delivered to your door.
The bottom line is... (0 Replies)
Just finished a quick Python script to send the current unix time over to the Arduino from macOS, so in the absence of GPS or some other way to get the unix timestamp (epoch time) to the Arduino, I can get my macOS and Arduino UNO synced to within a second.
Normally, when the Arduino starts... (9 Replies)
Here is a sketch to do basic testing for the Arduino UNO and the MLT-BT04.
This BLE module works with IOS (iPhone) and I'll add some details on my IOS testing with an iPhone in a follow-up post.
For now, here is the basic BLE (HM-10) sketch for the Arduino UNO:
/*
Arduino test-code... (7 Replies)
Discussion started by: Neo
7 Replies
LEARN ABOUT OSF1
ports
ports(7) Miscellaneous Information Manual ports(7)NAME
ports, port_names - Device (tty and lp) names for serial and parallel ports
SYNOPSIS
Default Serial Ports:
/dev/tty00
/dev/tty01 (not present on a single-port system)
Parallel Port:
/dev/lp0
DESCRIPTION
AlphaStation and AlphaServer systems provide one or two 9-pin serial communication ports. These ports are usually labelled 1 (COMM1) and 2
(COMM2), but they may be identified by different icons. Using the appropriate serial cable and terminator, you can connect a serial
printer, external modem, or character-cell terminal to a serial port. Most AlphaStation and AlphaServer systems also provide one parallel
port, for use with a parallel printer.
When you add a device to your system, the installation documentation may instruct you to map the device pathname to the port. These
devices are located in the /dev directory.
For serial-line ports, the two default device pathnames are: This pathname always maps to 1, COMM1, the lowest port number, an icon for a
terminal console, or the only serial port (on a single-port system). This pathname always maps to 2, COMM2, the next numbered port, or (if
one serial port is labeled with an icon for a terminal console) the remaining serial port.
If your system hardware has been extended to include additional serial ports, the pathnames /dev/tty02, /dev/tty03, and so forth, may also
be available to you. However, most systems have only /dev/tty00 and /dev/tty01 as the device pathnames for serial ports.
The one parallel port on an AlphaStation or AlphaServer may be labeled with the word printer or a printer icon. On some systems, the paral-
lel port may not be labeled. The device pathname for the parallel port is /dev/lp0. Currently, Tru64 UNIX does not fully support parallel
printers, so fewer devices are connected to this port as compared to serial ports.
If you are connecting a terminal console to your system, it must be connected to the serial port mapped to /dev/tty00. For other serial
devices, it does not matter which of the serial ports you choose for the connection. For example, suppose you are setting up a system that
has two serial ports, labeled 1 and 2. You intend to use a serial-line terminal rather than a workstation monitor as the system console and
also want to connect a serial-line printer to the system. In this case, you must connect the terminal to the port labeled 1 (with the
device pathname /dev/tty00). Therefore, you must connect the printer to the remaining port labeled 2 (with the device pathname /dev/tty01).
If, for the same type of system, you intend to use a workstation monitor as the system console, it does not matter which serial port you
use for a serial-line printer or modem. In other words, you can connect the printer to either port 1 (with pathname /dev/tty00) or port 2
(with pathname /dev/tty01). When prompted to enter a /dev/tty** pathname by the lprsetup script or the Print configuration tool in the CDE
Application Manager, you would specify /dev/tty00 if you connected the printer to port 1 or /dev/tty01 if you connected the printer to port
2.
See the System Administration manual for more information on setting up consoles (including remote consoles) and printers. See the
modem(7) reference page for more information on setting up modems.
SEE ALSO
Commands: lprsetup(8)
Devices: ace(7), modem(7)
System Administration delim off
ports(7)