12-02-2019
Yes, I noticed that (much later). Unfortunately I could not find this "inofficial" patch oss603a.
8 More Discussions You Might Find Interesting
1. Solaris
Hi Friends,
I am trying to execute rsh commands from Solaris 10 system to AIX system.
When I give;
Solaris10# rsh <hostname> ls -l , it gives me an error
rshd : 0826-826 The host name for your address is not known
At the same time,
Solaris10# rsh <hostname> ---- gives me remote shell of... (25 Replies)
Discussion started by: jumadhiya
25 Replies
2. SCO
After System power get failed
File system is not getting mounted in read- write mode (1 Reply)
Discussion started by: gtkpmbpl
1 Replies
3. Shell Programming and Scripting
hi all
I have a problem how to write a shell script which delete files/folder form directory whenever system boot and copy last updated folder/file in the specified directory.pse help me ASAP.
i write a script which copy files in directory.I want when system boot up using script it check whether... (1 Reply)
Discussion started by: shubhig15
1 Replies
4. UNIX for Advanced & Expert Users
Hi,
In order to have a sand box machine that I could use to test some system changes before going to production state, I'd like to duplicate a working system to a virtual one. Ideally, I'd like to manage to do it this way :
- Make a full system backup excluding the user file system (this... (7 Replies)
Discussion started by: pagaille
7 Replies
5. HP-UX
Hi all
I wonder if its possible to mount on a hp-ux server a file system that was previously mounted on a solaris 10 server. The LUN is on NetApp stoarge.
The problem on hp-ux I cannot do pvcreate on the lun (disk) because contains data.
Any help will be appreciated
FR (2 Replies)
Discussion started by: fretagi
2 Replies
6. AIX
I have a following requirement in production
system 1 : LINUX
User: abcd
system 2: AIX (it is hosting a production DB)
Requirement
user abcd from system 1 should have read access on archive log files created by DB on system 2. The log files are created with permissions 540 by user ora ,... (2 Replies)
Discussion started by: amitnm1106
2 Replies
7. AIX
Hello All,
I am trying to clone an entire AIX virtual machine to a new virtual machine including all partitions and OS.Can anyone help me on the procedure to follow? I am not really sure on how it can be done.Thanks in advance.
Please use CODE tags for sample input, sample output, and for code... (4 Replies)
Discussion started by: gull05
4 Replies
8. UNIX for Beginners Questions & Answers
In a nutshell requirement is to migrate the system from mainframe environment to UNIX environment (MF cobol would be used I guess). I have not much of idea in this field. I need to do some investigation on following points -
- Ease of conversion
- Known Data compatibility issue
- Issue in... (9 Replies)
Discussion started by: Tjsureboy4me
9 Replies
LEARN ABOUT SUNOS
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M)
NAME
addbadsec - map out defective disk blocks
SYNOPSIS
addbadsec [-p] [ -a blkno [blkno...]] [-f filename] raw_device
DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis,
but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be
fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI
drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software
remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping.
It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block
occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup.
OPTIONS
The following options are supported:
-a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be
quoted and block numbers should be separated by white space.
-f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file.
-p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option
cannot be used to print the hardware map.
OPERANDS
The following operand is supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec,
diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to
label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 addbadsec(1M)